Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi,
Is it possible to write/read the flash memory, from within the interrupt handler of GPIO? I used an push button connected to a GPIO to wake up the ble chip, then read...
Hi,
Does nRF5340 (or any other nRF52XX) support natively ISO7816-3 (SmartCard)?
"Natively" means using USART or any other way(hardware of official software) other than...
I am reading the PPI Example at the Infocenter as shown by the link below: -
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v11.0.0%2Fppi_example...
Hello Nordic,
I worked with the interactive PyACI during several months by using my PC (running the interactive PyACI) connected through usb to a DK used as provisioner...
Hello,
We've recently migrated from SDK version 15.2.0 to 17.0.0 and noticed an anomaly with the clock driver. If the watchdog is started, then after any soft reset (through...
Hello! How can I measure the heap size (total and free space) at runtime?
Right now I'm working with some legacy code that makes a call to mallinfo()
That call returns...
I am testing "nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\experimental\ble_app_cli" example.
Do I need 2 boards to run this example ???
What I got from the infocenter...
Hi
I am using SDK17. I am running the app_pwm example and i get an error with the "nrf_drv_state_t", it is not defined and the "NRF_DRV_STATE_POWERED_ON" is not defined...
Hello,
I'm programming nrf52 with SDK17. My application requires to advertise in 1 channel and also scan in 1 channel too. I have done the code. But when I run the code...
Hi,
I'm programming nRF52833 for my application. I have done to configure my device and it advertised and scanned sequentially. For my application, I advertise and also...
Hi:
I am trying the "Mesh Serial" example on my nrf52840 boards. However, when the Echo command is used after the device is cold-started , a timeout event will occur. I...
hai ,
i am using nrf52840 sdk 15.2 and in my application i have to connect nrf52840 central to peripheral after connection i have write data on ble_lbs_led_status_send i...
Hi,
I am using NR52832 with nRF5_SDK_15.3.0_59ac345 .
I want to scan nearby mobile BLE devices and get its data from its advertising data and also its scan response data...
Hi,
Hi, we have a latency-critical use-case and found the Low Latency Packet Mode ( LLPM ) as a possible solution.
Our current application is using nRF5 SDK 16.0 with...
