I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Greetings,
we have a custom pcb with nrf9160 and are using nrf-sdk v1.3.0 and mfw v1.2.0
Sometimes when connecting to lte the code crashes:
The code in question is...
Hello, I am developing with: custom nRF52810 board, nRF5 SDK 17, S112.
I'm using APP_TIMER for my main tick. I have the following code I use to initialize and start the...
Hello,
I am using SDK16, Softdevice S140 with SES.
I am trying to add DFU functionality in my application and leaving only the activation of the new firmware to secure...
Hello,
I am now working on a product concept which uses RTC module to retain date and time. To speed up the development, I started with ble_sdk_app_template and I am modifying...
We're using nRF52840 with S140 SoftDevice (version 7.0.1) and 16.0.0 SDK. When USB cable is connected before USB initialization we receive correctly APP_USBD_EVT_POWER_READY...
I am very new to the Embedded world and very confused about some stuff, I have searched the internet for 8 hours and then asked here.
I am being assigned to the task of...
Hi!
I'm developing application on nrf52832 development board which will be a work indicator - for office desk ;) Main idea is that i have client based on nRF MCU and desktop...
Hi, I am searching the nRF52810 product spec and see that with standard drive, maximum GPIO output current appears to be 4mA. However, this spec is given for when the output...
Hello, I am working on SDK 1.3.0, I have an NRF9160DK and I am migrating to a custom NRF9160, I would like to output the log by moving the pins of the UART. However, it is...
We have ported from SDK v15 to v15.3 but now have a problem getting the USBD to start.
Below is a sort of pseudo-copy of our USB init routine which is working for us on...
Hi,
On Nordic SDk 15.0, I have observed that USB CDC ACM Example is not working in interrupt mode on nrf52840 Evaluation kit.
But I have tested USB CDC ACM Example in...
I'm experimenting with nRF52840 DK
However, using break points in the main loop causes 'app_error_fault_handler'.
using the iar compiler. What's the cause?
Hi~
I have a question about the SAADC.BLE Connect Mode. When I turned on Saadc LP mode, the power dissipation was 0.02mA for single-channel sampling, but 0.5mA for dual...
Hi All,
I have looked through the devzone and cannot find a solution to this. I am using the nRF52832 SDK 15.2. Working with a BNO080 IMU over TWI.
I need to read more...
