I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
hello.
I am developing as nrf5-ble-multiple-role-example-master.
And I'm using nrf52832 chip.
When I send a message from the mobile app, I get a message on the...
hi,
I have developed light lightness model with the help of generic on/off and generic level model from the mesh SDK. And I have used these models by making changes in the...
Good afternoon,
I am trying to run the example "direct_test_mode" on a custom board based on a nrf52832.
I have succesfully run the example in two development kits ...
Hi,
I´m using nrf52840 with softdevice S132 and I wonder whether the ble_gattc_conn_cfg_t::write_cmd_tx_queue_size is a queue common for all connections or if it a queue...
I am currently testing DFU updates with nRF52. I have run into a situation where the upload of new image is interrupted for some reason. When I try to run the update again...
Target : NRF52832, SD S132 6.1.1. program on Eclipse.
Hello,
Intro :
I migrated to SDK 15.3 for my application and it works.
Then I migrated DFU to SDK15.3 too but...
Hello! I am developing a pcb based on nrf51822. I am trying to copy the layout of the PCA10028 at first. But I will not use the coaxial connector for an external antenna....
Hello!
I have next problem. When switching from backup power to main power, the controller loses data in RAM. If the backup voltage is below about 2.4V, then it is possible...
Hello,
I am trying to add bonding functionality with a passkey to HID device, and use for this ble_app_gls_pca10040_s132 example as basic project.
But it don`t want to...
normally the secCount in Eddystone TLM should be the t ime since power-on or reboot:
https://github.com/google/eddystone/blob/master/eddystone-tlm/tlm-plain.md
but the...
set the tx power of a tlm frame with the eddystone configuration service will result currently in an app error. call path is es_gatts_write_handle_unlocked_write -> es_slot_radio_tx_pwr_set...
The function documentation for pm_conn_handle_get says BLE_ERROR_INVALID_CONN_HANDLE is set to the connection handle pointer if the peer is not connected, however it is BLE_CONN_HANDLE_INVALID...
Hi,
I programmed nrf52840 dongle with simple ble_blinky example. The dongle successfully bond with my phone but when I tried to discover services and read characteristics...
Hi
I am working on nRF52832 DK and using Ubuntu 16.04 and Segger Embedded Studio as IDE. When I try to build the AES_CTR program, the following error comes up.
Can anyone...
Hi I have run a few peripheral examples ok and now move to evaluation of ble_peripheral also.
I'm using this version of the SDK....
If I program the softdevice and...
