Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hello,
Just received the nRF9160-DK and followed instructions but it seems there is no connection, only LED3 is blinking
Location is Belgium close to Brussels
Hi,
I'm using the PCA10056 dev kit to verify the workings of the DCDC converter. I added the following code after nrf_sdh_enable_request() :
e = sd_power_dcdc_mode_set...
Hi to all,
I'm new with the nRF52 DK developpement board and I use Zerynth ( Python ) for developping a simple application for a product who are still existing. ( MOKO M1...
Hello,
I am developing in Windows 10 machine in visual studio code. I cannot use Seggar studio. Devloping for nRF52840 dongle with nRF15 sdk.
I have written the below...
I am using SDK12.3 and the Flash Storage module to store some data in Flash. I frequently need to update some of these data basing on received commands.
When I use "fs_erase...
Hello,
we are developing a machine that is in pre-production. We need to be able to update the firmware and until now all works well on android. but on IOS the dfu does...
I'm trying to get the LTE Sensor gateway running on the nRF9160 DK. The documentation says to run the HCI:UART example on the nRF52840. When I click on the link for that example...
Hi,
I need to know if it's possible get the firmware work using 52810 with 192K flash. As far as I know, S112 takes 100K, APP with secure connection takes ~85K(ble_app_hrs_pca10040_s132...
nrf52832 S132 v6.1.1
i want to write saadc data in flash, so i call "write_to_flash" function in "void saadc_callback(nrf_drv_saadc_evt_t const * p_event)"
sizeof(data_array3...
Does anyone know if Segger Ozone is licensed for commercial use if used with Nordic Semiconductor devices, similar to the use of Segger Embedded Studio? Or, do we need to...
Hello Everyone,
As mentioned above I wanna know how to send Energy Expended data from nRF51422_xxac device to BLE mobile application using HRM characteristics or HRS Services...
Hi,
I'm starting to work with Nordic Semi Develoment boards with a Thingy:91.
And I wanted test the GPS module and send it over HTTP POST using the LTE of the Thingy...
Dear,
I am using :
ncs: v0.4.0
SES 4.16
firmware: mfwnrf916007029alpha
Hardware: nRF9160 DK v: 0.8.5
I want to do:
1. Enable and get GPS position ("AT\%XSYSTEMMODE...
Dear ,
I tried to use HTTP POST to POST the information from GPS to my webserver.
But I couldn't combine 2 of them together. ( they, GPS and HTTP POST, worked well separately...
The driver timer of the slave stops when the slave disconnects with the master. The deviation is caused by the disconnection as the following picture shows. The hardware timers...
