Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
There is a note in the eddystone configuration service specs ( https://github.com/google/eddystone/tree/master/configuration-service ) in characteristic 4:
Note: if a power...
About the case where there is no sample project of NordicSDK multirole (ble_central_and_peripheral) Hello. The other day, I purchased Nordic's BLE module and started developing...
We are going through testing with FOTA, our AWS IoT deployment and AWS S3. Fota is initiating and downloading the file properly through MQTT commands but fails after 4096bytes...
Hello,
I am using the nRF52840-DK to implement a zigbee light device.
If I use another nRF52840-DK to act as a coordinator, the light bulk example works fine. However...
Hi
I'm using a custom board with nRF51822 and mbed.
Then, I would like to generate 25kHz PWM and use BLE simultaneously.
So, I read this thread, write like the attachment...
Hi,
I am porting the opus library from smart remote project into our system. The chip is nrf52832.
When I encoding the pcm data, I got error. After tracing into code...
I am trying to port an application that works on the NRF52 DK board to a custom board containing a 52832 QFAA chipset. The MCU is connected via SPI to an IMU BMI160 and a...
hi all,
the latest master fw-nrfconnect-nrf. asset_tracker project gps_controller.
now ,i try add gps_control module to my project. but it now work correct that gps_controller...
I built my project with SDK 15.0 but for some modifications I migrated to SDK15.3
In my application I use pairing key to secure connections but since migrating to SDK 15...
Hello,
How to ass custom button using BSP? In the default setting, there are only 4 buttons. But my custom board has more than 4 buttons. How to add more button using BSP...
Hi, I have a question on USB performance of nRF52840. I have Rigado BMD-340(s) and I have to verify the maximum data rate supported on USB interface. Its says 12 mbps in the...
Hi
There are two PCA10090 DK boards. Each one had its own iBASIS card.
Previously, I registered these two in nRF Connect for Cloud. DK board A with SIM card A.
DK board...
I have ordered some PCBs which have I2C lines on P0.08 and P0.09 and have been trying to test using the Dev Kit and for some reason, I can't get any traffic out of these pins...
