Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Windows 10, Keil5 5.27.1.0, Nordic SDK 15.3.0 59ac345, pca10056 devkit for nRF52840.
Works:
The DK shows up as "JLINK" when plugged into USB. I can copy the prebuilt hex...
I am currently publishing messages to a group of servers on a 10 second interval. This works well for a while but after a few minutes some of the nodes stop handling the message...
Hi! I am using Nordic Thingy : 52 Iot Sensor Kit. I have Windows x64 computer. I connected the sensor's bluetooth (nrf52832) to the HM-10 bluetooth module. I want to transfer...
I modified mqtt_simple program to test eDRX. This program subscribes a topic right after it is initiated.
I want to test only eDRX so set keep alive time = 30 min
I...
hi,
I am trying to readout the UICR info. But there is no such readout in the hex file using the programmer apps in nRF Connect.
There are 2 possibility, either blank...
Hi,
I am using nRF52832 DK and also my custom board based on nRF52832.
I have uploaded the application file into my device using OTA-DFU.
Now my device goes in application...
In my computer, I receive the error below
Besides that, the error also stated this: "Zephyr was unable to find the toolchain. Is the environment misconfigured?(Refer to...
Hi there,
I'm sorry if I'm asking something very simple:
How does one connect the J-Trace Pro to the nrf52 DevKit in such a way that I can get ETM functionalities? Obviously...
hi:
my chip is NRF52832 (512k FLASH + 64k RAM).
I want to triggle ESB send process by PPI + TIMER ,but i can't find the function like esb_task_address_get()，but i found...
I tried finding a link to a porting guide mentioned in few of the posts in the devzone but couldn't find a working link. I have a project originally meant for nRF52832 devices...
I'm getting confused with the following statement, taken from www.nordicsemi.com/.../S132
"It supports up to 20 concurrent links in all roles."
So, I will try to explain...
Hi everyone,
I am trying to connect multiple peripheral and collect the rssi values of the the peripheral devices in central mode. After collecting the rssi value of the...
I want to send Digital Microphone data from one device to the other two devices. So which BLE and micro-controller should I use for better performance? I am totally new to...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I connected my sensor to nRF52832 DK over TWI...
