Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I would like to instruct my application to read the battery voltage on my nRF52pca1040 DK, I am intending to do so through the SADC.
I will feed the board with...
Hi,I have some problems in debug with experimental_ble_app_buttomless_dfu project.
First i build the experimental_ble_app_buttomless_dfu project,so i get the app_buttomless...
We am improvising nrf blinky application, we have got stuck in a problem, after button is pressed from nrf52-dk code goes into forever loop and after a while connection is...
I have two nrf51822 modules and first one is sdk8.0.0 / s110 / peripheral device, second one is sdk10.0.0 / s130 / central device. I've sent a 10-character data array like...
Using:
SDK14
Softdevice132 V5.00
app_uart driver with legacy, no easy dma.
UART is set up with hardware flow control.
The pins should be set up correctly: rx-tx , cts...
i want to konw ble evt struct 's content of meannig . i want to find what's the return value when packet send fail and what is the channel id different from other ruturn value...
Hello,
I want to falsh nrf51422 device. I ma developing software using Eclipse and SDK_7.2.0.
The soft device is 130. I have build the project successfully and Hex/elf...
Hi
I'm trying to communicate between nrf51-DK and arduino using twi. I was able to send data from nrf51-DK to arduino using nrf_drv_twi_tx but when I'm trying to send the...
Reference PWM_driver sample code,
I set the customer status of the LED,
And it also can change status by button,
static void bsp_evt_handler(bsp_event_t evt)
{
void...
Hi,
I want sample code for configuring baud rate of UART from mobile application (nRF Connect). So I don't need to hard-code the baud rate in my program.
Please share...
With version v2.0 of S332, I checked for a return of BLE_ERROR_NO_TX_PACKET when using the ble_nus_string_send function. I use this test in a routine which writes buffers...
I called these command:
nrfjprog -f NRF52 --eraseuicr
nrfjprog -f NRF52 --program app.hex --sectorerase
During the eraseuicr I see:
Erasing UICR flash area.
Applying...
Hi there,
for my Application, I want to listen for all BLE packets on a fixed channel.
No SoftDevice is used.
I receive all packets as long as BASE0/1 and PREFIX0/1 and...
now, i have a question: i have a buffer 100byte data to send, when i send data package via sd_ble_hvx() continus,delay 20ms after each send ,but it will lost some data , i...
HEllo,
I am facing and issue with undefined references for the linker. The compiler is able to compile, but I get linker errors like these
.../pca10040/s132/arm4...
