Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,
I was using Nordic's Master Control Panel for a while to upload firmware to my nrf51822 BLE beacon for a while and now I want to move one step further. I want my...
HI,
In the BLE Spectification, both of the inquire and scan can find out the advertising slave role device.
what's the difference between them?
And Is it true that...
I am trying to emulate the case where a scanned peripheral goes offline before the connection was issued by the user by calling sd_ble_gap_connect() with a completely made...
Hi, Guys,
I have occured a wired thing. I use NRF51822 with softdevice S130 to do a BLE project. I use both spi and twi to get information from sensor(I use spi0 and twi1...
Hi,
In my application I need to keep both time and date so I need a real time clock & calendar (RTCC). I was planning to use on the nRF51 real time counter (RTC) to implement...
Hi.
I'm trying to declare an uint16_t array while programming on the NRF52 Development kit as follows :
uint16_t FinalSignalArray[225000];
However, I keep getting...
I want to read the nrf51 memory, I'm using nrfjprog.exe --memrd 0x0 --n 0x40000 > name.txt
but get something like
0x00000000: 20000C58 00000115 0000012F 00000131 |X....
Hi All,
I need to read the data written on RX characterstics of nrf_uart Service from my board using bluez.
I'm using interactive mode of gatttool with my Nordic sensor...
Hi,
I need to design a small nRF52 board, with a 3cm by 3cm size. I am very new to antenna design, so i have some questions, in order to avoid ruining it. The reference...
I'm trying to write 32bit word on flash memory every 25ms, but when I read the memory using nrfjprog I noticed that it write only 16 words (32 bits), in this code saveToFlash...
1,How do I send a data packet using BLE Peripheral? What API should I call? How should I prep that API? Do I have to care about the format of the data that will be sent, or...
For starters, I'd like to use an Arduino Uno to receive a Bluetooth signal from the nrf51 DK and
turn an LED on/off.
What materials do I need to do something simple like...
Dear Nordic developers,
SPI_MASTER peripheral behaves in a way, that I cannot understand from manual is it normal or no.
I have implemented something similar to loopback...
