Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
The documentation says that: " By default, threads run in supervisor mode and allow access to privileged CPU instructions, the entire memory address space, and peripherals...
Dear Community;
I am trying to send some data via Lora with a nRF9160 connected with SPI to RF95W Lora module. The transmitter is a nRF9160 with a RF95W, and the receiver...
Hello,
We're piloting updating our sensor beacons RuuviTags to use Coded PHY for better range. The current design has nRF52832, our update would be to drop in a nRF52811...
Hi Nordic Support Team,
I am trying to combine
..\nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_s140_ble\ses
and
..\nRF5_SDK_17.0.2_d674dde\examples...
Hi,
I have been looking around the forum and have found conflicting information regarding the existence of a QSPI flash driver and example for the nRF53 on Zephyr. Is this...
Hi,
I am trying to run nrf zigbee light bulb sample provided in the nrf SDK on the NRF52850 usb dongle.
I have sucessfully built "blinky" app sample with NRF Connect SDK...
Hello Everyone,
I am developing one product for the HVAC system. I have Radiator and STM's primary MCU. For development, I need to configure the thermostat cluster ID for...
Dear Nordic Community,
Because of unavailability of nRF52840 we are shifting the work to nRF5340. I have some queries on this topic as follows,
1) Is SDK will be changed...
Hi Nordic Team,
I am new to Bluetooth mesh and NFC. I am working with the device nRF5340 and SDK NCS v1.5.0 .
I have used the sample Bluetooth: Mesh light as a starting...
Hello, I'm trying to use PN532 module with nRF52840 using I2C. the data can be sent, but when it comes to read it, IRQ keeps high, so it reads 808080 .. I added a nrf_delay_ms...
Hello,
Starting with the example of mqtt_sn_client_publisher in the nRF5 SDK for Thread and Zigbee and I want to publish an array of data like this one
in a MQTT topic...
I am trying to send some data from nRF52840 to Xbee via Zigbee In this case, I set nRF52840 as router and Xbee is the coordinator. I use zigbee_cli_agent_router sample code...
Just took delivery of a new THINGY:91 from DigiKey - v1.4.0.
Trying to follow the steps in the User Guide, but when I plug into my Macbook, it's not showing up as a USB...
Hello,
I'm a CS student and I'm trying to work with nRF5340 DK. I'm trying to program the sample network_coordinator (Zigbee) to the board using SEGGER Embedded Studio,...
Hi,
I try to use the nRF sniffer but it can't capture any packets.
System used :
Windows 10 Pro x64
Wireshark 3.2.0
Python 3.8
nRF Connect v3.3.0 - Programmer...
