I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hi!
I'm working on the NRF52832. I'm using the function "nrf_serial_write()" to send data over uart. I want it to work in blocking mode. As I can read in the infocenter...
I am working on BLE development and need to study the BLE heart rate collector and peripheral examples. I plan to flash ble_app_hrs onto nRF51422 and ble_app_hrs_c onto nRF52840...
I am using nRF52832 SDK 15.3 and type 4 tag and some phones like iPhone 11 and Samsung S20+ are not able to detect the tag. The tag works with other phones so I don't think...
Hi there,
I'm using nrf52840 DK and Custom board, SDK 17.0.2, Segger Embedded Studio(SES v5.20)
my issue is when I receive data from UART interrupt based on serial uartes...
I'm developing a system of nRF9160, nRF52832 and Iridium 9603 (satellite modem) - all on the same main board. The nRF9160 is the brain of the system and handles LTE, GPS and...
Hi,
I am new to working with nrf52840 devices. I am wondering if it is possible to change the transmission power of packet during transmission several times such that some...
I wanted to increase the bandwidth of bluetooth using the following example, but there is a limit of only 1 board.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17...
project : zephyr
controller stack : zephyr stack
description ： we start direct adv using our DK，and we want it send broadcast only once。 but zephyr stack send adv all...
Hi,
I am working on NRF52 series (NRF52 DK and NRF52832) and would like to know whether it is possible to use Bluetooth 5 extended advertising capabilities to send, let...
Hi there, I'm routing the nrf9160 to a STM32 and I need to know the pinout for COM port used.
On my PC, I know COM11 is the one that is used for AT Commands
But, I...
Hi,
I'm using NRF52840 with direct test mode application.
I'm sending to the function dtm_cmd following parameters: 0x4000, 0x8000, 0x9400, 0xA500.
I understand...
Hi,
After suspending task in a specific code line (using vTaskSuspend) and resuming the task (using vTaskResume)- will the task continue from the specific suspension line...
I am going to make a project with nRF52840 In my application, I need to send sensor data to Raspberry Pi I noticed this tutorial and tried to implement this in my project...
i tried to implement radio notification in order to change advertising data but i had this error
when i put the periority to LOW i get this error, if put MID or HIGH the...
