I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hello sir,
I am working on my final PCB design using nRF52832 chip. As per your reference Bill of material i use same part number for all components recommended by you. But...
I have a custom board with the nRF51822 QFAA . Schematic:
In order to compile the firmware, I'm using MinGW . As you can see, I'm also using the SDK 12.3.0 .
Finally...
Hi,
I am using nRF52832 and softdevice is S132 adk13.1. My application is read 3 ADC channel one by one and send this value to android app using NUS. For this i have use...
Hi,
We are performing data transfer using NUS service (BLE-UART).
Data passed is a 11-character string.
READ and NOTIFY permissions are provided for Tx characteristic...
Hello,
I am designing NRF52832 based board. I followed the exact reference layout suggested by Nordic except via position. I moved few vias during routing. Is it necessary...
I am using segger studio and jlink to program my nordic thingy 52. I followed the documentation and
Build the program
Connect to Jlink
Erase All
Debug->Go ...
Hi!
nRF52. S132, SDK13.
I try to use ble_dfu_send_hex example.
what shoul I do first?
via nrf gostudio load SD. correct?
Which SD? from this folder (dfu_test_softdevice_s132...
I get the mesh SDK here: http://www.nordicsemi.com/eng/Products/Bluetooth-low-energy/nRF5-SDK-for-Mesh/(language)/eng-GB
But I don't know how to add pwm to the light_switch...
Hi all,
I use the nrfjprog 9.7.1 and unfortunately I was used the --rbp command on my nRF52832 and now it's impossible to execute --recover command.
The nrfjprog log shows...
Hi,i have some problems when develop with experimental_ble_app_buttonless_dfu project in sdk12.3 on IDE embedded studio (MAC OS).
I follow this link text to develop.when...
Hello,
Some problems I meet when I try to use spi manager in ble_template example to read "who_am_i" register of LIS2DH12. The environment is set as below:
nRF52832...
Hi,
I'm using SDK13.0.0 and softdevice S132 v.4.0.2.
I sometimes get NRF_ERROR_INVALID_STATE from sd_xxx() in the function registered to ble_evt_dispatch() when connection...
Hello,
I would like to establish communication between my pca10040 and my cellular modem.
Currently I am using ble_app_uart on the peripheral example and I can put messages...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I have a thread using a Timer and PPI to trigger SAADC sampling at 100hz. Currently I have an app_timer also running at 100hz to sample the results of the SAADC (and its time...
