Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
I see there is a differenece between v1.0.0 and v1.1.0 in the asset tracrker's main loop.
i.e. poll function vs the sleep function.
does this result in a change...
Hi,
I'm working on a custom bootloader which does DFU over I2C. As a fail safe mechanism I want to have a timer running that gets reset between each Image data block, so...
When using SDK v13's I2S driver, the data to send is filled via data_handler callback. How do I fill last block data?
Assume i2s buffer size is 2000, then every 1000 words...
I have been going through the steps in this blog post: https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/getting-started-with-nrf9160...
Hello everybody,
I'll try to modify the ble uart example. The target is, to get data from two different nus Services (different characterisitv uuids). They are both initilised...
I basically need to use two UART instances with the BLE Buttonless DFU Template App.
I started using the Serial library but apparently it's no longer supported.
The methods...
Hello,
I am working on nRF52832 SDK 15.3.0 in segger studio.
In my project I have 2 ADC input pin.
ADC initialization is as shown below,
And every 0.5 second I read...
I have a custom BLE characteristic that I want to use to allow an app to send commands to my device. I use an on-write() function that is called whenever a BLE_GATTS_EVT_WRITE...
The Device's name UUID for Thingy52 in according to this site https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/firmware_architecture.html is: EF68xxxx...
Hi I am using nrf52840 on a custom board with segger embedded studio as development IDE. I would like to flash the hex file generated without using segger embedded studio...
do you have a user gide for Serial DFU just like buttonless DFU ,like this link https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics...
Hi,
I have flashed lte_ble_gateway on nRf9160 DK (PCA10090) and hci_uart on nRF52840 SoC.
After flashing, I am getting some random RSSI values and MAC Address , instead...
Hello,
I have two micro-controllers communicating over SPI.
The STM32F746 is SPI master. The nRF52840 is SPI slave. I use SDK v15.3.
I am sending two bytes over SPI...
Hi.
I had to unpair from the Android Bluetooth list by doing pm_peers_delete () when bonding. It's ok. I know why it should. But sometimes I can't find my paired device...
