I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
I am working on blinky example and want to modify service/characteristic uuid. I do
that in ble_lbs.h as follows:
//#define LBS_UUID_SERVICE 0x1523
#define LBS_UUID_SERVICE...
I had the following setup, two app_timers triggering blocking SAADC reads in the callback functions
app_timer 1000ms triggering 1 Blocking SAADC read (For battery service...
Hello,
I use sdk 8.0.0 and s110. I read this blog
And I did not understand some terms;
Application processing(for example 2ms each adv interval)
Number of packets...
Hi,
I am using the nRF51 Dongle (PCA10031, V 1.1.0) and pc_ble_driver.py to create a custom script for testing purposes. But there seems to be a maximum limit for the measured...
I met a problem when delete bonding information on android central, i actually can't connect to the nrf52832 peripheral again, until i totally clear it's peer list and bond...
Hi all,
I am trying to control a speaker using the i2s output of the nrf52832 mapped into a TAS2505 from TI. I am able to play sounds in the speaker but my issue is that...
I am trying to use the eddystone example I found in the ble_prepheral/ble_app_eddystone/pca10040 folder in SDK14.2 with my nRF52832 development board but I get the following...
i found this link on nordic website to learn ARM with Nordic SOC.
www.nordicsemi.com/.../Nordic-ARM-Lab-in-a-Box-University-Program
Do you know where is the link for...
Hi,
I am able to program a SparkFun nRF52 breakout board via nrf52 Dev Kit using Segger Embedded Studio. However, I am not able to achieve the same results using nrfjprog...
I am facing some issue while writing to i2c. On first i2c write , device is working but after that when i tries to write anything, code is stucking in loop.
void sensor_sleep_mode...
Hi,
I'm trying to port my project from SDk12.1 to SDK14.0, I've got everything working fine except the DFU process. The main issue is that we've got some devices distributed...
Hello,
I am designing a custom board with NRF52832 IC. I followed all PCB consideration suggested by Nordic.
This blog suggests, If using a PCB antenna, the matching network...
This question is similar to this thread:
devzone.nordicsemi.com/.../
However it was framed differently and didn't really clear anything up for me.
Say my application...
