Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
Hello,
Ble spec says that "new alert" characteristic - field: "category ID" can have 1 or 2 bytes.
here
But it seems in your struct you let it have only 1B.
typedef...
Hi,
I have ordered a PCB using the reference schematic for NRF51422 user guide.
I wanted to know whether the schematic has the required antenna design or I need to add...
Hi All,
I have a basic question about advertsing data, more precisely about device's address.
I try to disable in my advertising data, the address field but it doesn't...
Hi I followed the Nordic UART example code to read and write characteristics to a Nordic S110 nRf51822 device.
My code is the same as in writeRxcharacteristic but when...
When I'm single stepping my nRF52 application in Keil with a BLE connection I always get the softdevice_fault_handler called.
I'm using SD 132, v2.0.0 and the the parameters...
What is the maximum clk frequency that can be output on a gpio for the nRF52832 ? I want the nRF52832 to output a clk signal on any of the gpios to an external module, and...
Can anyone please suggest a simple example on initializing SAADC Driver on one pin and do a simple blocking ADC read?
Sorry for a very broad question - but rather to ask...
I'm using the nRF52 Dev board and set the --rbp ALL option while using nrfjprog. It worked fine, and I am able to do OTA updates as I was testing the bootloader example. But...
Hi
I'm doing one project that is taking data from uart and send to mobile app. I'm facing one issue that is when I connected to peripheral it connected and take data from...
I'm looking for some options to extend the PCA10028 with a keybord and a numpad. This would give great options to play around with passkey topics.
As the PCA10028 supports...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Hello,
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board. The ANT Updater shows that the Image Upload is completed. I am uploading the...
Hi,
I there a way that I can detect if a sections of my code has been interrupted by the Softdevice? I have some time critical code (bit banging a communication protocol...
Hi All,
I am using the nrf51422 and softdevice S310 to send out ANT+ and BT Smart in my project.
I use RTC1->Counter in order to get a timestamp for an interrupt from...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
