After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
I am using a Fanstel BT Module BT832F (that utilizes the Nordic nrf532832 chip). I am able to successfully run my code on Nordic's dev board PCA10040 and also Fanstel's dev...
Hello,
I have found a bug within the current (and earlier) release of the NRF SDK.
I have a project where I am using ESB to communicate. There is a primary transmitter...
Hi! I am trying to enable UARTE and Serial in my app, but somehow the nrf_serial code is not compiled because it fails the "#if NRF_MODULE_ENABLED(NRF_SERIAL)" test.
How...
Hi,
We have a legacy product which is in production using the nRF51422 using a legacy DFU.
We need to re-install some test equipment PCs with Master Control Panel which...
Hi,
I' m trying to create a TMIM easydma sequence to same an ADC. The sequence involves a write, and timer delay and a read.
Given what I'm trying to achieve, I think...
Hi ,
Is it possible to send low rate telemetry data ( 1Kbyte) per day
to smartphone VIA Nordic NFC solution.
So ... the smartphone read the stored memory in nordic...
Hi teams,
As the title describes, how can I find source/destination address inside mesh model callback functions?
Is there any API functions? Or should I modify callback...
During the pairing phase, LTK will be generated for the secure connect, and no LTK will be generated for the legacy pair, but LTK will be generated for the subsequent bonding...
Where can I find documentation of http://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.2.0/nrf/samples/nrf9160/serial_lte_modem/README.html#serial-lte-modem IP UDP low power...
Hi, I am trying to create a custom_service for my application.
I am using nRF52832 SDK_16
SES
I want to create the BLE_SERVICES
which has send characteristics and...
Hi,
I converted ble_app_beacon example to Segger Embedded Studio (using version 4.30b), as per the instructions in the link https://infocenter.nordicsemi.com/index.jsp?topic...
I configured a NRF52832 with non-scannable and non-connectable as well as scannable/connectable advertising. Everything is working fine.
But I want to fully understand the...
I have an existing phone app (using the traditional GATT system), and I would like mesh-enable my products so that if the products can see each other, then the phone can connect...
nRF51822 PS says standard drive GPIO output voltage will be VDD-0.3V ~ VDD In our previous project w/ nRF51822, I found it to be very close to VDD when connected to GND via...
