Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
nRF52811 has only one receiver. Most accurate direction finding can be made based on estimation of phase difference between two signals received in two spaced antennas. Such...
Hello – My project needs to report its indoor position to the cloud (no GPS). I intend on using known positions of iBeacons SSID/RSSI coupled with trilateration math – fully...
Hi team, I developed own project based on /examples/dfu/secure_bootloader/pca10056e_ble/ses/. In the original project there was only Release config (no Debug). I modified...
I am trying to figure out how to configure my peripheral such that when a central client tires to enable the service changed characteristic that it succeeds. I am desperately...
I'm working on an application where I will need to initialize the modem, send/receive messages and then turn it down to low power until the next checkin. I did a real simple...
I have read that at each connection event master will send the first packet (empty payload).
In a case where slave latency > 1, the slave will not be listening to master...
Hi devs,
It is not a real issue it is about a possible misconception about app_timer
For my application, I am using multiples timers using app_timer_create. From my understanding...
So I'm coming to the nRF52832 from a couple decades worth of light occasional programming, mostly data analysis and scientific computing in nature, and primarily in C/C++...
Hello,
In my setup, I have 5 clients (buttons) that all report to the same server (lightbulb).
I'm using the Mesh SDK 3.2 light switch example with static provisioning...
Hi everyone, I successfully followed all the steps of the Getting Started Assistant on Windows 10 x64, but I am unable to open the Asset Tracker project because of some errors...
Hello, I was building the asset_tracker application in segger_embeded_studio v418 on Mac OS. I am using master branch( because we need real gps data), however, I encontered...
I know that master sents "LL_CHANNEL_MAP_REQ" to slave to indicate that there is a new channel map. I want to know does master keeps on doing channel sensing to know which...
Hi,
I am using SDK15.3 and nrf52832. I am using multilink central example to connect to my peripheral device. I have one peripheral and one central device.
As soon as...
Hi,
I am using below setup
nRF52 Development Kit
pin_change_int_pca10040 example application provided in SDK
Segger Embedded Studio on Windows 7 64 bit
I have...
