I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi,
I'm using nRF5 SDK V12.0, I found a strange problem. That is the UART can send data to PC, but it cann't receive data from PC. However, this problem just arise on some...
Hi,
I need a bit of help to fully understand how ADC works on nRF52832.
I am using a Thermistor sensor like the following to measure temperature:
Epoxy Thermistor...
We would like to use the PPK for automating some of our tests. Is there any documentation on how to drive the PPK over RTT? If push really comes to shove, we can always read...
BLE UART This is a problem that I have discovered while checking
the cause of the connection frequently due to communication error.
It is normal... In the nRF52832,...
Hi,
I added following code in saadc example code to set GPIO pin high/low and monitor it in the terminal. The pull up looks ok, but when I set it to low, the reading never...
We created our own PCB for the NRF52 with a Johanson chip antenna but no matter what we do, we can't get a signal from the Antenna, not even a weak one to show up on the spectrum...
Hello,
I duplicated the project example "nrf51-micro-esb-master" under "proprietary_rf" and got it up and running. I now need to incorporate some timer functionality.
...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
As I've tested by using
err_code = sd_ble_gap_address_get(p_addr);
APP_ERROR_CHECK(err_code);
App returns...
hi
i am using nrf51822. i used the radio tranceiver example and it works well. I am planning to advertise the received packets so that the range can also be increased and...
Hi all --
I have a tricky layout "issue" where unfortunately, I've ended up connecting my I2C device to the BlueTooth module on the side of the module where my VDD isn...
I'm reading the SDK 10's GPIOTE doc and I'm wondering if there is a way to read a GPIO state without generating an event, ie, something like foo = PORTx.pin10 or alike.
...
Hi,
I have a central that is trying to pair with a peripheral. I want this connection to be secure and I want to use ECB for encryption of data. My peripheral does not have...
Hi,
I'm trying to communicate the nrf52832 with a LIS2DH accelerometer and when I'm trying to read 192 (32*6) bytes of data (to empty the entire accelerometer's FIFO) my...
Hi,
I want to know what is my execution time for each function.
I am using nrf51822 chip and the IDE is IAR Embedded Workbench.
How can i calculate the execution time...
Can I detect overflow on RTC1 when using timers with S130?
In my App, I use timers but also count time with NRF_RTC1->COUNTER. I need to know If overflow happens.
It seems...
