I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hello,
I have a custom board which has NRF52832 SOC(i.e. main MCU) and another ARM Core-M0-based MCU(i.e. target MCU). These two are connected over I2C. I wonder how to...
nRF BLE sniffer is crashing within the first few minutes of use. Attached is the log of one sniffer
session from the start to when it crashes.
Here is my log.txt from...
I'm working my way through BLE Advertising, a beginner's tutorial and getting a SDK error 4001 when trying to use
advdata.include_appearance =
true;
Can anyone...
Hello!
I'm trying to nRF52 soc chip to drive the matrix sensors array (16x16), because there is no enough I/O pins for my project and thinking of use the shift register...
Hello everyone,
I have a program which set configurations by using write (nrf_drv_twi_tx) in the registers of a sensor.
I use the SDK 8 in the nRF51.
Here is the code...
Hello, I want to test using RTT for logging since I am using UART for send/receive packets. I made following changes in sdk_config.h:
#ifndef NRF_LOG_ENABLED
#define NRF_LOG_ENABLED...
I have device with nrf5x and I will customize this device on production. I use to flashing nrfjprog.
Will prepare one hex file and customize e.g serial number during flashing...
Good time dear Engineers!
Faced with a general Problem.
I use two nRF52 boards connection : Central <-> Peritheral.
init data: MIN/MAX conn intervals = 10/30 ms
...
I noticed that the GPIO port read and port write for SDK v12.2 changed to accommodate chips with more pins but I can't find much information about it. How do I use nrf_gpio_port_out_read...
I want to make a frequency of 750khz, 50:50 duty ratio.
How do I use pwm?
I use it. nRF52832 PCA10040
I used the PWM library example but it failed.
The frequency...
I'm using nRF5SDK V.12.2.0.
In the app_ble_uart example, trying to change MTU size as below.
#define NRF_BLE_MAX_MTU_SIZE 103
...
#if (NRF_SD_BLE_API_VERSION == 3)
...
I am using SAADC with TIMER3 and PPI, sampling 12bits at 250Hz.
When I use 10uS acquisition time, the average current consumption is 300uA lower than when using 3uS or 5uS...
With nrf Toolbox 2.2.1 on android 6.0.1 (Google Nexus 7 or OnePlus 3T), I try to transfer an application firmware in a zip file UiBoardV0.4.1.zip , generated with "nrfutil...
Hi,
In am using a nrf52832 in a serializated configuration, with the softdevice S132 on the connectivity board.
Is there a way to configure GPIO on the connectivity...
hello,
i have one nrf51 dk and it has some advertisement packet, i have another nrf51, i want this another nrf51 to copy first nrf51's data. can you tell me how to copy...
