I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hello,
For my Thingy91 I want to do some simple HTTP POST. I had a look at the https client sample (nrf/samples/net/https_client) and thought It could be a good baseline...
Hello, I'm developing on an application which requires to catch high speed, variable size and bursty (~0.5 Mbit/s) data from a sensor connected to a nRF9161DK trough a UART...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hello,
The subject of this post is mostly accurate in that I am developing custom hardware that is based on the nRF7002DK. For all intents and purposes, the Interface MCU...
Are there any unique design considerations to take into account when using the nRF54L series with RRAM? For example, are there any concerns about magnetic fields causing bit...
Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
Where can I obtain the security certificates (e.g., client certificate/private key) needed for TLS authentication with nRF Cloud? - Are these generated during device onboarding...
I used Nordic52480 DK(bulb) as DUT to run Matter Certification case TC-DGGEN-2.1 .
Steps:
1. setup OTBR on Pi4：./certification-tool/backend/test_collections/matter/scripts...
hello all,
I'm fairly new to nRF SDF and its build environment. I browsed a lot of posts but did not find the solution to what is probably a basic misconfiguration error...
Hi all,
We've been doing automatic network selection (+COPS=0) but are looking into moving to manual network selection.
When trying to search for available networks...
In nRF cloud, in the device list ( https://app.nrfcloud.com/#/devices ) it is difficult to manage larger number of devices because of lack of search and limited sorting. ...
Hi,
I am getting randomly incorrect SOC reported by pmic npm1300. For most days, it reports correct SOC but then all of a sudden it starts to report incorrect SOC even though...
Hi, I've encountered a change in behavior when upgrading from NCS 2.9.1 to NCS 3.0.1 regarding MCUboot and watchdog integration. In NCS 2.9.1, I was able to enable the watchdog...
