Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
1,I use nrfgo studio and can download softdevice ,it is OK.
2,I use the s110 example,it runs ok too.
3,I modify something from the example ,and click debug(keil),but it...
1,I use nrfgo studio and can download softdevice ,it is OK.
2,I use the s110 example,it runs ok too.
3,I modify something from the example ,and click debug(keil),but it...
I would like to be able to do a sanity check on the CHIP ID.
The Product specification states:
"No ID will violate the rules specified in section 6.4.3.2"
Section 6...
I am finding it difficult to figure out what is the minimum toolchain requirement to get started developing using the nRF24LE / U.
Is Kiel the only compiler ? Can SDCC...
Hi,
I have nRF51822 DK with (s110_nrf51822_7.0.0, nRF51 SDK_v6.1.0.0) and when i try to run the project in IAR 7.20.2 i receive an error.
2 ) My icf file...
Hi!
I have bought the nrf51822 EV KIT and it came with 5 extra nrf51822 modules but them without a board. I have researched a little and I found that I need the Segger...
Hi,
We're using an off the shelf module with a trace antenna that can't be modified.
Measured the module once assembled, and due to surrounding plastic materials, the...
Just finished upgrading to the latest SDK Version -- and trying to build some of the examples -- but consistently getting compilation errors when building any of the nRF51822...
When working with BLE, one sees a lot of different names for roles, which is confusing. What is actually the difference between them all, master, slave, central, peripheral...
Hello to everyone,
I'm developing a new project with a nrf8002 and a Smartphone with Android 4.4.2. Both devices connect to each other fine, and I can bond them with no...
Hi,
I made a peripheral firmware based on "s110\experimental\ble_app_uart" example, but I don't know how to write a central module FW so that these two can pair to each...
The reset handler as shown in the C:\Keil_v5\ARM\Device\Nordic\nrf51822\Source\templates\arm\arm_startup_nrf51.s will call SystemInit as defined in the C:\Keil_v5\ARM\Device...
Hi
im unable to connect nrf51822 EK with nrfgo studio
how can i solve this issue
m using all latest version softwares
and wen i click ok it shows as below
...
Hello, i know its an often discussed topic but i already read lots of threads about it and didnt find the answer.
I have a simple program that enables the softdevice s110...
