Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
Hello,
In nRF Connect for Mobile, custom UUIDs show up as unknown, making it difficult to identify them easily.
Is there a way to add custom UUIDs, as can be done for...
Description:
I am experiencing a non-linear "sticking" and "jumping" behavior when attempting to monitor the VDDH rail using the internal VDDHDIV5 channel on the nRF52840...
I don't know where to make this suggestion, so hopefully my suggestion makes it to the right person.
I completed BLE Fundamentals and the nRF SDK courses.
I would have...
Hi! I'm migrating some code from an 14.2.0 SDK to the 17.1.0 SDK and cleaning up a big mess.
Whenever I call nrf_power_pofcon_set ( true , NRF_POWER_POFTHR_V27) with either...
I am trying to debug/flash an nRF54L15 using the nRF Connect VS code extension and a J-Link EDU. Although my J-Link EDU works fine with all the Segger tools, including Ozone...
Hi
I am looking to a wearable / health tracker which will be mounted on a persons head.
Are there any precertfied nRF7002 module where I don't need to go through the pain...
We tested several hundred connection and disconnection cycles with the nRF52840 BLE dongle. The first hundred cycles operated without any issues. However, at a later cycle...
Hello, I am trying to use twister + ztest to run some basic tests on my device custom project and nrf5340 Here are the contents. Current Directory Structure
Contents of...
Hello there,
I'm developing a project with NTN using a Vivo chip, a Brazil operator chip, but I'm having trouble with an nRF9151 and I'm trying to put it in NTN mode, but...
Hi
I took over a nordic project and was asked about the bluetooth version used in that project.
How Do I figure this out?
I am using a nrf52833. The firmware is developed...
Hi all
While connecting to a peripheral that has ble buttonless dfu characteristic i need to enable indicate.
Undortunately i get back err: 0x11(17) from sd_ble_gat...
I'm struggling with the nrf sdk v2.9.2 zigbee light_switch example. I copy the example, add this to proj.conf
CONFIG_ZIGBEE_CHANNEL=25 CONFIG_ZIGBEE_CHANNEL_SELECTION_MODE_SINGLE...
Hi.
I have a question.
When sending packets from a ZIGBEE product (with TI CC2538 built in) and receiving them with an nRF52840 Dongle (Sniffer FW) and Wireshark, is it...
Hello Everyone, I was wondering if there is any easy "ready configuration" way to directly set BLE advertising and connection interval with adding some config to the prj.conf...
Hello! Using NCS 3.2.1 I am implementing DFU over SPI (the NRF54L15 is SPI slave) using the "DFU Target" library. It works very well, as long as I am connected with JLink...
