Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Recently s110_nrf51822_7.0.0 softdevice has been released. I cannot find specification where those new amazing features (they are impressive, indeed :) ) are described, so...
Hi All,
Please correct the following in my understanding. Also , i am planning to build a
remote controlled device using a PWM output. How does ATT,GATT and GAP affect/influence...
My board works most of the time are very good，but one time i power down the board when ble connecting and data transmitting，the board can't work when power on.and i can't...
Hi,
Can somebody explain how the Ax, Bx and Tx registers are used in the calculation of the temperature reported by the temperature sensor block in an nRF52832?
What we...
Hi,
I need to connect multiple SPI slaves in a daisy chain. It seems that using nrfx_spim_init once and nrfx_spim_xfer at each transfer is the simplest way to go using the...
hello, i want to synchronyze differents peripheral with a central thanks to the state of gpio i have this code but when i call gpiote() i hava nothing in return why ?
void...
I have done some reading on the forums and have seen that Martin Bohrs-Lind has ported the EMDv6.12 to SDKv14.2 and the nRF52832, here . I have keil v 5 compiling his work...
Hi
What would be the best way to interface a wireless charging circuit with a nRF52 device?
I've found a IC from Texas instruments that does the job, but is it safe to...
Hello,
I am using sdk12.2.2 and nrf52832 customized board. I am putting mcu to sleep mode using sd_power_system_off. Now when I am pressing button for first time I am not...
Using the include files and .dll file from
www.nordicsemi.com/.../nRF51822 -> "DOWNLOADS" -> "nRF51-BLE-Driver-Win" I have created a C# wrapper for the driver. I works so...
Hello,
I'm using multiple GPIO pins as inputs. Should I use nrf_drv_gpiote_in_event_enable() for each pin? Also how to configure the input_event_handler() to handle the...
Hello,
I'm a beginner on BLE protocol and i would like to send data during approximately 4us,stop it during the same time and transmit signal again during 4us and so on...
Hi
I’ve downloaded nRF5_SDK_11.0.0_89a8197 and starting with examples from \examples\ble_peripheral\???\pca10040\s132\arm5_no_packs\
I'm writing an application to be running...
Hi
I am new to ARM and Nordic programming.
I want to send one HEX byte via SPI.
It works with some HEX numbers and with some numbers it wont.
0x13 / 0x15 work
0x14...
I wonder if it is OK to change the lpcomp ref input on the fly, without any other stop task or disable/enable. Just like this:
//--------------------
static void lpcomp_set_ref...
i want to print the data to the uart to see the values in the uart..i am unable to initialize the uartt..
what are the things to be added for the initialization of the uart...
Hello I need to increase the maximum number of servers for clients to 100. I saw that in the light_switch_example_common.h file, the definition #define SERVER_NODE_COUNT ...
I am developing on a nrf52 board and trying to use sd_power_reset_reason_get(&uint32). This function should only be able to return succes, but I always get back 1. I saw a...
