Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello,
I have loaded the ble_app_blinky_pca10056_s140 example to the nRF52840DK and it works fine with the nRF Blinky mobile app. I modified the Blinky example code to...
I am working on a program that uses both CoAP and GPS in the form of thread. Since both CoAP and GPS uses the modem, I have to turn it off so the other thread can use it....
Hi
I want to change the advertising Company ID from Nordic to something equal to the Company ID used in one of my vendor models.
In previous topics some people say it...
Hello.
I wanted to know what the gpio state when no power is connected to the device.
I have connected a RTC battery to one of the ADC channels via a series 100K resistor...
Hi Nordc Technical support team;
My name is Ercan. I'm from Turkey. I am a Master degree student in Electronics and Communication Engineering department.I want to make a...
I am adapting the example ble_app_uart_c_pca10056_s140, which is a BLE Nordic Uart Service central device. I would like that other c files can access the variable m_ble_nus_c...
Hi Everyone,
I am working on the nrf52832 and i am trying to build the Eddystone beacon application example with segger embedded studio. But when i do, I get the following...
Hello,
I want to modify the default transmit power of the nrf5340 peripheral_uart project.
board:nrf5340 dk
ncs:v1.5.0
example:v1.5.0\nrf\samples\bluetooth\peripheral_uart...
I am trying to figure out how to enable and use the RNG peripheral of the nRF5340.
since the RNG is on the Network side of the nRF5340.
is there anything i need to set...
This is very reproducible...after sending and receiving data in a loop, the modem application becomes unresponsive. Only modification from SDK software is that I am using...
Hello,
I was trying to setup nrf5 board with IoT sdk for tcp connections where the tcp board will act as a server and raspberry pi 3 model B 1.2 as client.
I downloaded...
I am looking for the following products and solutions.
Products :
nRF52-DK
External input :
ADC 1000 Sampling input
1Hz input 3.3 p-p sinewave
Output :
UART...
Hello Sir/Ma'am,
I have used the ble_app_uart (for pca10056) example code to execute the same.
I referred this link to execute my code https://infocenter.nordicsemi.com...
Hi there,
I am using nrf_mtx_trylock.
The explanation of nrf_mtx_trylock is "Try to lock a mutex.".
I would like to lock a mutex forcibly.
Does the function which...
