I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hi,
I dowloaded mesh 5.0 sdk and open light_switch example project with SES which installed in a 64bit windows 10.
I set the SDK ROOT as following the step of online guide...
Hello,
I have just started in the world of Nordic products and quite recently in the embedded world. I'm trying to learn and understand the use of zephyr in basic projects...
Hi,
after migrating functional project to latest ncs version v1.5.0 I managed to build and flash it to nrf52840 board without problems. However if I enable MCUboot option...
Hi guys,
I want to add the function of multiple slaves to the nrf_desktop routine to support two hosts to connect to the keyboard .This routine is in the ncs1.4.1\v1.4.1...
Hi,
My application is to scan BLE advertising packet.
My application works when the scan_phys is set to BLE_GAP_PHY_1MBPS.
params.active = true; params.interval = NRF_BLE_SCAN_SCAN_INTERVAL;...
I'm specifically interested in the predefined SPIMn - SCK, MOSI, MISO, SO pins for this device, so that I can marry this information into my CPU Schematic Page. Whilst the...
Hello,
In our application, we have an external watchdog IC. We need to test the timing of that chip during our board power-on self-test.
We currently achieve this by setting...
Hello!
Recently we have noticed that some of our devices has been reporting strange fulgurations on their reported battery level. This is a graph over 24 hours:
When...
Hi I am the evaluation board of nRF52832 (TAIYO YUDEN Evaluation Board) EBSHSNZWZ) is used. I want to use P0.09 and P0.10 of nRF52832 as PIN of GPIO(TWI). It was set according...
Hi,
I'm developing a serialization system with nRF52832 and an application chip. My product is a power-sensitive.
The code of ble_connectivity in nRF5 SDK 17 calls nrf_drv_clock_init...
I've run into an issue with FOTA updates. The issue can be described by the following sequence of events:
A device is completely erased and programmed with a binary image...
Hi,
I am working on programming a bootloader on a NRF52840 DK using a different NRF52840 DK. Currently I have them connected via the debugger and have been successful in...
I am trying to port my build from Eclipse (based on the GCC tool chain) to a KEIL uVision build system.
I am using KEIL ARM Compiler version 6.15. Most of the files compile...
I see many similar questions to this, but I want to double check my understanding.
We have the nRF52840 connected to D-/D+ on a USB Type-C connector. We have a standalone...
