I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
I am trying to compile hci_lpuart for thingy91_nrf52840, but I have these issue. hci_lpuart:
Any ideas on how to solve this? I'd really appreciate it. And if you have any...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
I have an NCS v2.6.1 project on the nRF52832 where I'm using both the zephyr timer APIs
and the nRFX TIMER drivers
This causes some perplexing issue where my Zephyr...
Problem with exercise code in a developer academy fundamentals course.
Exercise:
Bluetooth LE Fundamentals Lesson 2 Exercise 3
SDK:
v2.9.1
Board Target:...
Hi,
I am encountering an issue with the TWIM driver when attempting to communicate with the nPM1300 PMIC via I2C.
This problem seems to be related to the behavior of the...
I attempted to create bluetooth central and peripheral apps using two nRF52840 boards that connect to each other and no one else using the device name. I had limited success...
We are developing a light product that features a built-in button. A single click of this button toggles the light on/off, while a long press adjusts the brightness level...
I tried flashing my nrf9151 after running the set-up and loading the AT modem. I then tried to reflash the board but get an error. See below:
2025-07-10T12:53:00.281Z INFO...
Hi!
I have been unable to find a single, simple set of instructions for adding MCUboot to a project(toolchain 3.0.0 sdk 3.0.0) that will enable a non-default signing key...
Hey All
Im working on a new product and its the first time I'm developing around the nrf5340, I'm looking for some guidance around the supply configuration for maximum...
Hi everyone,
just a quick tip that may save you some debugging time when using the nRF Connect SDK Build Configuration Editor in VSCode.
If you explicitly set a Base configuration...
Hi,
I'm using thingy91 for several weeks now and wanted to erase everything to start again from a clean basis.
I followed the guide https://docs.nordicsemi.com/bundle...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hello, I am running BT together with MPSL timeslot. When timeslot ends and RADIO and TIMER10 are cleaned up and a new timeslot is requested I get following HARD FAULT:
What...
