Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
I am working with SDK15.3.0 and a PCA10040 with S132. I have two questions relating to the BLE addresses as seen by the PCA10040 and by nRF Connect.
Q1 - What is the relationship...
Modem firmware version 1.0.0
Segger version v4.18
nrf tag v1.0.0
Often when I try to flash a new build of an application and try to flash an application through Targert...
Dear Team,
I want to integrate an nRF chip into my Project. I will use a ready made module from Laird, the BL652-Sx.
For Debugging I want use the nRF52 DK and connect...
Hi all,
we would like to add usb-cdc support for our nrf mesh project. I have tried merging an usbd example project into our application but without success so far. I am...
When I try parse string on nrf52832 with SEGGER Embedded Studio for ARM 4.16, I have a problem about "sscanf" :
Here is code:
It should output:
Num: 12
Num:...
Hello to all! I use the sleep mode PWRDWN = 0x04 and periodically wake up at WDT.With that, I see needles for the current consumption in the circuit to wake up the circuit...
I measured the output power over all the channel, see graphics below. It is not much, but i still would like to know why the output power drifts over frequency. Is this by...
Hello,
I have two nRF52832 (BL652) modules setup and connected through an RF cable. I am feeding the peripheral radio (2x) 174 byte packets every 5 ms. On the central, I...
Hi,
nRF9160 mqtt works with ipv4 by using "ncs\nrf\samples\nrf9160\mqtt_simple" application.
Now NB-IOT network which we are using is faced out the IPv4 and moved to IPv6...
So we have a great set of 52832-based set of products in the field that negotiate, agree to, and support MTUs larger than 23 bytes. Nordic's is incidentally one of the least...
Hello everyone!
As far as I've read in the manual, Power Monitor allows to export measurement data to file and use the for further processing. I'm using Power Monitor v2...
Hello,
I am using ublox B201 for my project which is based on nRF52832 SoC & with use of SDK 12.2.0.
So i need to know which IDE supports nRF5 SDK 12.2.0 ?
As segger...
SWDIO,SWDCLK,VCC AND GND have been taken out from the nrf52810 ic and proper connections have been made to the jtag end of the j link device (connecting all grounds also)...
