Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi, I'm looking for a PCB antenna design for nRF52832 based on 0.8 mm thickness four or two layers stack up .
I found some examples but based on pbc of different thickness...
Good morning,
I'm designing a new product based on the nRF52840 device (s140) and power consumption is one of the key parameters for my project.
The equipment (peripheral...
I'm debugging some corner-cases with my own DFU process and Bootloader. I believe I hit a race condition in which sd_mbr_command() was called before the source of the new...
I am trying to make a service discovery on a peripheral device using a nrf52-DK (pca10040). I built my project around the multi-discovery example from SDK 15.3.
When performing...
Hey all,
I'm trying to replace the nrf_cli_uart transport layer with the CDC ACM equivalent (nrf_cli_cdc_acm), since I have an nrf52840 dongle and can't use the uart libraries...
OS : Ubuntu
SDK: 15.3.0_59ac345
Base example : peripheral/saadc
HW : nRF52832 DK PCA10040 1.2.1 2017.49 682663245
Hello, i would like to make sure the ADC acquisition...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I want to check for debounce of a level on...
Dear support,
What are the absolute minimum decoupling cap sizes running the nrf52810? The application is extremely power sensitive and it is not desirable to have any...
Hello
I am trying to add two custom UUID as below ( Platform nRF52) . And the API return error when I call the second time, with a different UUID .
err_code = sd_ble_uuid_vs_add...
Acually i m working on a project which calculates distance using RSSI values , and i am having this doubt whuch examples to refer between ble_central and ble_peripheral
...
Hi,
I want to configure "BLE_GAP_PHY_2MBPS" in ble_app_uart example of sdk 15.3.0 for faster communication, for this i have changed
BLE_GAP_EVT_PHY_UPDATE_REQUEST: { ...
Hello community,
I am trying to obtain minimum current consumption in dk. I found lot on internet but currently there is no example code for RTC and PSM mode.
Can anyone...
