I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi all! :)
I struggle to initialize GNSS when I don't have a connection with LTE. Examples that could be found on dev academy initializates GNNS after LTE has been initialized...
Hi Nordic team.
I'm finding a way to update the factory data over-the-air. Specifically, I want to update the Matter Certification information (PAI, DAC, ...) over-the-air...
Hi，
In Core Specification v5.4, there is support for Non-Connectable and Non-Scannable Extended Advertising (ADV_EXT_IND) without AUX packets. However, when using Nordic...
When both ethernet and WiFi are supported on one MCU (with both sharing the same L2 implementation, only one network device being active at a time), does it matter if both...
Hello,
I'm working with a custom board using an nRF5340 as its primary MCU and NCS 2.7.0. The application I'm developing requires internet connection and can ideally support...
I am adding OTA support using mcuboot with mcumgr on a custom nrf54l15 board with the upgrade (mcuboot_secondary) partition on an external SPI nor flash (not QSPI). I am using...
we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
Hi!
I am trying to power the thingy:91 from solar panels and have some issues with the thingy:91 restarting when the solar panel receives a medium amount of light. The solar...
Dear Nordic TS,
I'm trying to power an nRF9161 DK with a simple external battery. According to the documentation, I thought that this battery voltage should be applied between...
Since I need zephyr version 4.0 or newer, I tried updating my project to the nRF Connect SDK v3.0.0 as well as the toolchain. I know that they are not fully released yet....
I'm trying to flash a custom board (schematics in this ticket - Schematic/Layout review request ) using a Jlink EDU mini and keep running into an error message saying it's...
Hello,
I am a beginner when working with nRF. I am trying to run the l4_e3 solution code, but it doesn't seem to work. I can connect via BLE, but nothing is being shown...
I am currently in the process of filling out the 18031 RED Cybersecurity certification documentation. I am currently analyzing the security vulnerabilities list of NCS v1...
Hi,
We’ve designed a project using the nRF5340 + nRF7002 combination, with Wi-Fi connectivity enabled.
As part of our preparations for FCC certification, we’re currently...
