We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi,
Would like to understand when will be the chip select pin be asserted and de-asserted when reading/writing a QSPI external flash?
What will enabling QSPI by setting...
Hello and to whom it may concern
I am currently using nRF51422_QFN48
with laser marking on the IC body
N51422QFAAF01616CS
i am using nRF desktop connect and try to...
Hello,
I'm having this problem with this nRF24L01+ connected to an ESP8266 (ESP12-E on BOB), and I'm using NodeMCU 2.2.1. The nRF24L01+ module I'm using is a small board...
Hello everyone,
i have a problem reading data from MAX30101 sensor FIFO. I set up the sensor and enable all 3 LEDS (Red, IR, Green), but when I read the data from the FIFO...
I'm using nRF Connect v1.5.0, Zephyr, and Segger Embedded Studio (SES) to develop an application I'm testing on nRF5340-DK.
I have a project that compiles and runs. But...
Due to the recent semiconductor global shortage, we are changing the chip on our device currently on the market from the nRF52832 chip to the newer nRF52833. I am in charge...
RNG interrupt handler is not called.
Using nrfx_rng library to generate random numbers.
VALRDY event is generated but interrupt handler nrfx_rng_irq_handler in library...
I have looked at the UART example provided in the NRF52 SDK. The example uses the UART in blocking mode. I need to create a version that is non-blocking, and only reads the...
Hello Nordic,
I was looking at multiprotocol support from nRF Connect SDK by following this link: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_multiprotocol_support...
Hi
Trying to install and operate the Sniffer based on nRF52840 USB Dongle
Having the nRF Connect for Desktop installed and burned the Dongle in accordance with the instructions...
Sorry I have to see how the ssp of ublox work.(nina 410)
II have to send a packet over the serial every 50mS.The packet len is 100byte.
I see that some time the received...
Hey DZ,
I'm having some trouble with the download_client. It's not playing nice with the HTTP server I'm using. On the last chunk of data, the nRF91 is issuing a Content...
Hello everybody.
I am developing a firmware which allows us to send data bidirectional between Central and Peripheral. On the one side we have a nrf51-DK and on the other...
