Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
I tried to debug UART communication between 52840 development board and 9160 development board. I sent 9 bytes of data from 52840 side, but I only received 8 bytes of data...
Hi,
I can't find how to get data received by interruption of UART. I've used libuarte example and I tried to get data from buffer buf in uart_event_handler, but it doesn...
I can see that other people have run into the "no code for breakpoint" problem when attempting to use the SEGGER debugger. I have read the earlier posts. I have not been able...
Dear Sir/Madam,
Can you please help to check and advise if both part# nRF52840-Dongle and nRF52840-DK have KC certificate? Thanks.
Best Regards,
Dan Lee
Hi,
I'm using for awhile TIMER0 and I want him completely disable.
I'm setting a TASKS STOP to stop a timer, clearing a interrupt and disabling interrupt in NVIC, but...
I'm looking at the datasheet for the NRF52832 because I'll be using it with a Raytac module and I'd like to know for sure how the SPI pins are set.
I see in the datasheet...
hi, i've used the official zephyr version till some days ago. the reset pin worked. now i've switched to the zephyr version "supported" by nordic and the pin reset isn't working...
I did the multilink central function when I used zephyr OS Connecting the five peripherals is stable at first, but after a while the error of <err> bt_att: ATT Timeout will...
Hi Everyone,
I have been developing with nrf52840 for quite sometime using Arduino. I would like to explore nrf5 Sdk for Zigbee and Thread because I want to use my nrf52840...
When I generate bootloader settings using nrfutil 6.1.0:
The output indicates the start address is 0x3fc00:
However, looking at the hex file, it contains identical...
I'm measuring the current of the following code:
I'm not using softdevices.
I have nothing more connected to the board than the power.
I measure about 0.320 uA which...
I'm trying to make a test app that includes sample code from GPS and udp examples.
Building for nRF9160DK with west.
Here's my Kconfig:
```
# # Copyright (c) 2020...
Please help me to eliminate the error : "cannot open source input file "nrf_erratas.h": No such file or directory" for nrf51422 for nrf 51(12.3) sdk in keil version 5
Hello, We noticed that when we enable the whitelist, we can successfully filter out connection requests, but not scan requests. Our device still responds to every scan request...
