Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello – My project needs to report its indoor position to the cloud (no GPS). I intend on using known positions of iBeacons SSID/RSSI coupled with trilateration math – fully...
Hi team, I developed own project based on /examples/dfu/secure_bootloader/pca10056e_ble/ses/. In the original project there was only Release config (no Debug). I modified...
I am trying to figure out how to configure my peripheral such that when a central client tires to enable the service changed characteristic that it succeeds. I am desperately...
I'm working on an application where I will need to initialize the modem, send/receive messages and then turn it down to low power until the next checkin. I did a real simple...
I have read that at each connection event master will send the first packet (empty payload).
In a case where slave latency > 1, the slave will not be listening to master...
Hi devs,
It is not a real issue it is about a possible misconception about app_timer
For my application, I am using multiples timers using app_timer_create. From my understanding...
So I'm coming to the nRF52832 from a couple decades worth of light occasional programming, mostly data analysis and scientific computing in nature, and primarily in C/C++...
Hello,
In my setup, I have 5 clients (buttons) that all report to the same server (lightbulb).
I'm using the Mesh SDK 3.2 light switch example with static provisioning...
Hi everyone, I successfully followed all the steps of the Getting Started Assistant on Windows 10 x64, but I am unable to open the Asset Tracker project because of some errors...
Hello, I was building the asset_tracker application in segger_embeded_studio v418 on Mac OS. I am using master branch( because we need real gps data), however, I encontered...
I know that master sents "LL_CHANNEL_MAP_REQ" to slave to indicate that there is a new channel map. I want to know does master keeps on doing channel sensing to know which...
Hi,
I am using SDK15.3 and nrf52832. I am using multilink central example to connect to my peripheral device. I have one peripheral and one central device.
As soon as...
Hi,
I am using below setup
nRF52 Development Kit
pin_change_int_pca10040 example application provided in SDK
Segger Embedded Studio on Windows 7 64 bit
I have...
I've been trying to get debugging working with the STLinkV2. I'm not able to step into code whatsoever, when I pause execution it appears t PC is at:
Info : halted: PC...
