Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
We are using the nRF5340 for Thread communication and an Ignion BLE Antenna (NN02-101) for range testing.
During the range test, we observed an RSSI of -25 dBm at close...
Hi all,
In our project we are using two device running on NRF chipset. One has the s140 softdevice version ( NRF52833 ) and the other has s112 version ( NRF52810 ). We are...
Hi,
I need help to disable shell_uart and its commands used in UART of BLE mesh chat example as i want to configure this UART for custom protocol along with RTS signal to...
Hi Nordic:
I am currently working on Bluetooth Matter product certification and require the certification materials for the nRF54L15. While filling out the application form...
I am using a custom board with a nrf5340 chip on it with vs code and sdk/toolchain of 2.9.1 and the bmi270 sample. I am getting and issue with my bmi270 accelerometer when...
Hi,
The nRF9151 DK product page indicates that the DK includes among other documents the hardware schematics and layout files. I've purchased the DK kit, but as far as I...
I am trying to build an application on nRF Connect SDK on VS Code and I keep getting this error:
c:/ncs/toolchains/0b393f9e1b/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc...
Hi All,
I am experiencing a significant voltage drop issue with the NRF-PPK2 device after a recent firmware update. When I set the source meter output to 3000mV (3.0V) at...
Hi All,
PPK2 isn't accurately measuring currents below 20 μ A, showing 0 nA instead. This started happening after you updated your nRF Connect software, and reverting...
I am using the nRF52840, nRF5_SDK_3.2.0, using example: usbd_cdc_acm. I mofified the example so that I transmit characters from a serial port to the USB using a virtual COM...
I have tried init modbus RTU on my nRF9160 with SDK2.5.2 using max485 module but i have faced an error. This is the error: *** Booting nRF Connect SDK v2.5.2 *** [00:00:00...
Hi forum ,
pls help me for flash erase ,write and read to be successful for windbond w25q64 here i m stacked a long days if possible pls send me a sample successfull code...
Hi,
I noticed that NCS has been updated to version 3.0.2. I now want to compile the beacon in host-only mode and make it work on the nRF52832, but I haven't succeeded so...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi,
I'm trying to set up SEGGER SystemView on our custom nRF5340 board for debugging purposes using the SEGGER SystemView application.
Below is the configuration I'm using...
