Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello, I’m using nRF52840 with SDK 16 and SD 7. My purpose is to save as much power is possible using high-frequency clock (32MHz) only during periodic duties and BLE activity...
What are best practices for updating an nRF52832 via UART from an nRF52840? There seem to be at least two problems to solve:
Transmitting the 832 image via BLE to the...
Hello,
I'm measuring the idle current using a PCA10040 DK, SDK v16.
Finding that the idle current is about 3uA (which I think is correct) after any debug operation like...
Our setup is using a NRF52832 with SDK15.0.0.
While working with a time sensitive external circuit where we both sample the state of the GPIO and enable LDETECT on it...
I have just received my nRF52 development board and I have tried to program one of the pre-bjui;t examples (Blinky). The USB drive on the board appears and if I drag the hex...
Hi,
I'm using an application with FreeRTOS , nRF52833, SDK 16.
When I'm trying to get it into low power (sleep mode) the system still consumes ~4mA
In vPortSuppressTicksAndSleep...
Hi,
I am starting with PPK. Tried some measurements on ble examples and looks like i am doing something wrong. I have aproximatelly 7mA during advertising. Am I doing something...
Hi,
i have load existing program to new nRF52 module. But it shows NRF_ERROR_NO_MEM.
Same old module doesn't show this error. i also reload the soft device. But no improvement...
I'm looking to implement the following security schema:
The peripheral does not have a display nor input capabilities
A smartphone will connect to the device
The peripheral...
I can use the nRF Sniffer to capture packets , but info "Empty PDU" is more and more, I want filter it. Please kindly help me how to operate it. Many thanks!
Hello. I have 3 peripherals connected to 1 central. The BLE_GAP_EVT_TIMEOUT event occurs in Central. Occurrence timing is random, p_ble_evt->evt.gap_evt.params.timeout.src...
Hi,
We are developing a solution with our partner company based on nrf52833 using S140 softdevice.
I would like to change the advertisement power after every advertisement...
I'm new to the nRF5340 and zephyr and ncs, but I have gone through the tutorial series https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts...
I'm trying to look at the nRF log for the temperature example I found in examples/peripherals using my nRF52840 development kit.
My laptop is windows and I have the DK plugged...
