We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi
We will use the 52811 together with nRF9160 for short range communications. Currentconsumptionwise which interface is recommended, UARTR, TWI or SPI?
I am trying to run the example secure_bootloader\pca10040_ble_debug. The application does crash during a debug print with following stack trace:
Any idea what could...
I've reached a critical point in the firmware development process where I need to start considering integrating a bootloader with the application code.
I have a custom board...
Hi,
I'm trying to update the modem firmware on my nRF9160. I believe the current firmware is mfw-m1_nrf9160_0.6.8-30.alpha. I followed Martin's suggestions here , but nRF...
Hi,
If i had a purpose of including Ble files into peripheral example then what is the way i can approach?Is it by including all neccessary header file paths,adding sources...
I am working with nRF52832 platform and using some Bluetooth examples like blood pleaser and heart rate. I am wondering how I can count the number of data transferred bytes...
Hi, I try to combine example Blinky with Uart. but i have problem error as link below
Output/blinky_pca10056 Release/Obj/main.o: in function `uart_init':
undefined reference...
Hello,
I am a new user.
I am currently trying to use the 1NCE and Hologram sims, and using LTE Monitor to check the connection.
I am able to see that the signals are...
In our application we use nRF24AP2-USB for some time now.
To test the ANT antenna we use a test program called "USB2_IQC_Test.exe".
This program compares a DUT with two...
I currently have a piece of firmware that uses SDK 15.3.0. The application that have developed that makes extensive use of PPI channel 1 to drive ADC sampling with a timer...
Hello, I'm just starting to experiment bluetooth with the nfr52840 DK board and the sample programs available, especially those "ble peripheral" and as a beginner I started...
Hello,
1) I am using the PCA10040 to program a nrf52811 chip on a custom board with SDK 15.3.0.
2) I'm using the example ble_app_uart_pca10040_s112 on uKeilV5
3) Initially...
Hi I wonder if there are any PPS signal from gps part to the cpu, preferable some kind of timer input or interupt port so it is possible ta make absolute timestamps with fractions...
Hi,
We are using nrf51422 in our project.So right now i am loading the program using the Usb cable .Here my doubt is can we able to flash the program by using usb to uart...
