We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi
Can you please point me to some documentation which shows how to run SD140 with freertos on an 840 chip?
Look forward to hearing from you
Kind regards
Mahendra
When I try to connect my device(iOS Application) to my peripheral(BLE Device), I want to send this passkey programmatically during the connection. I'm using BleManager but...
Hi,
a dumb question. For a board with voltage regulator installed is it allowed to connect SWD VTref to the regulator input (at <VTref1> point)? It's assumed that VTref...
Hello all
I've read various other threads concerning this topic, but I still can't wrap my head around it.
What I think I understand of this topic:
ATT_MTU can be...
Hello,
I'm trying to configure two TWI slave devices on the same TWI bus on my custom board(nRF52832). One slave is RTC, and the other is a biosensor. The TWI configuration...
Currently, I am using SES for development. So when I use the "Build and Run" option in SES the program runs properly. This also generates the .hex file in the Release folder...
I need to set HEX value (uint8_t value[7] = {0x56,0x45,0x52,0x53,0x49,0x4F,0x4E};) on my custom character to be read by my phone. but the value that is displayed on my character...
Hi,
1. I have been trying to measure the current consumption of the development board of nRF9160 in PSM mode, however, until now I could have not understood the role of...
Hi all,
I'd like to pass bootloader version (2bytes) from bootloader_util_reset function (bootloader) to the main of application. can help me to acheive that?
Thank...
Hello,
We are facing recently an issue that is very weird because it is not occuring every time. Indeed, the issue occurs after a DFU update, sometimes when the application...
My nrf51 DK Board is not detected by Keil as jlink probe, but with other tools. As a result I am unable to download demo projects to my board.
unmodified nrf51 dk has...
I'm working in SDK 14.2, and trying to send a single byte over SPI between two NRF5 boards using the SPI peripheral examples (1 master and 1 slave). However, SPI always seems...
Hello!
There are no hex files that are pre-made for the ble_app_interactive example. When I use VMware to run a Linux environment on Ubuntu to get an executable with gcc...
Hello,
I want to configure my nRF52840 development kit for counting input pulses on one of the GPIOs (Pin 13) in this case. I am using SEGGER Embedded Studio as IDE.
Here...
