We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi, guys. I'm using PCA10056 and SDK 15.3's BLE UART peripheral example.
I also have a Microsoft HoloLens (the first version which runs Windows 10 and the HoloLens shell...
Hello
I am working with LIS2Dh12 accelerometer sensor interfaced with SPI 2 of nrf52832. For its one of the axis we have configured the interrupt which is working fine individually...
hi,i am using nrf52 DK kit. i have interfaced it with bmd 101 ecg sensor. The sensor sends continuous data over UART. I am using SEGGER IDE. The code which i am using is ble_app_uart...
Hi there,
I'm confused with the meaning of the 'vloc' variable in the attribute meta data. In the example code ble_bps.c of "ble_app_bps_pca10040_s132" , in the function...
Hello,
We are experiencing an issue that some of the nRF52832 is not starting up automatically. But we attached it with JLINK debugger and didn't do anything, it can boot...
Dear Community,
I'm including a wireless bootloader to enable firmware updates in my application. My question is the following:
Before entering in DFU mode from my app...
Hi,
I am currently facing a coming issue by using the function net_pton. Under MacOS I get the following error:
1> app/libapp.a(main.c.obj): In function `inet_pton'...
I've got this logs while running out of the box the light switch example in zigbee sdk v3.1. I am connecting to a smarthings hub.
<warning> app: Production config is not...
I'm attempting to write a plugin/dll to pull data from the Nordic Thingy52. I can scan all devices that are paired with windows 10, and load up the services, etc.
I can...
Hi,
I am trying to replicate the benchmark numbers stated by Nordic for the nRF52840 to verify I have setup the chip correctly for maximum performance. I have caching turned...
Hi everyone,
I try to send my nRF52 DK board to an android application.
nRF52 example source is "ble_app_blinky_pca10040_s132" and Android app sample is nRF-Blinky from...
Hello everyone,
I am trying to develop a windows application using the same example from pc-ble-driver-4.1.1\examples\heart_rate_collector/main.c. When i call the function...
I am currently working on a project where I try to send data from a swimmer in the open sea to a point on the land (beach). I know that Bluetooth communications are blocked...
