Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I changed the I2C pins to below, and it not work. so is it possible to reconfigure the I2C pin? what should I do since I already set to 8&9 in the hardware board? const nrf_drv_twi_config_t...
Hi,
Looking for some ground on getting the netowork parameters set for a zigbee device, My intention is to limit the number of scan intervals and the scan time to save power...
I'm planning wireless conference system. This needs some condition as under simultaneously use 5ch of wireless bi-directional connection through whole system. Each wireless...
Hi,
I am using nRF52832 soc to develop my project. with nRF5_SDK_15.3 . SES file
I need to connect both BMI160 accelerometer sensor and AT24C512 EEPROM ic in TWI.
how...
I am trying to update firmware that uses v14 of the nRF5 SDK to firmware that uses v15.3, but I am getting the error "Init command larger than expected.".
I'm wondering...
Hello everyone,
I'm running the IoT CoAP example on my nrf52840 Development Kit.
The border router is Rapberry 3 B+ on Jessie with Kernel version 4.19.46. I've put BLE_6LOWPAN_LEGACY_MODE...
I am using nRF5SDKforThreadandZigbeev300d310e7 sdk for thread example simple_coap_client. I try to add uart module with simple_coap_client and i have added uart configuration...
Hi,
I am running nrf52840 on a custom board, SDK 15.0.0, softdevice S140 6.0.0 and SES.
In my application I am reading an IMU ( ICM20602) and a laser ranger/Time of Flight...
hi,master.
Question 1: In Asia, the speed of accessing web pages is slow. SDK15 development documents can only be accessed online on the official website, but often cannot...
Hi,
I am running NRF52840 on a custom board with SDK 15.0.0, Softdevice S140 6.0.0 and SES.
I am measuring using a toggled GPIO pin measured on a CRO. This produces a...
I'm using an nRF52DK to monitor the RSSI and MAC address of my two phones through ble_evt_handler BLE_GAP_EVT_SCAN_REQ_REPORT.
I tested both Android and iPhone. They both...
Hi all!
I have small problem. When I build my project, it returns thise error: Symbol SWI2_IRQHandler multiply defined (by nrf_sdh.o and nrf_drv_swi.o). I want to use SWI0...
