We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
We are trying to do final optimization of the load capacitors connected to the 32MHz crystal on the nRF52840. A value of 13pF for both capacitors results in a frequency that...
Hi,
Using SDK 15.0 via legacy nrf_drv_power, the nrf_drv_power_sleepevt_init causes fault:
It calls nrfx_power_sleepevt_enable but never calls nrfx_power_sleepevt_init...
I am working with Thread on the nRF52840 and have setup a few nodes and a Border Router 1.0.0 as described in the documentation using Raspberry Pi 3B+.
My sdk is nRF5_SDK_for_Thread_and_Zigbee_v1...
Hi
I was wondering if it's possible to scan for both 1MBPS and CODED at the same time, or should I initiate 2 different scans.
using this configuration initiates error...
Hello,
we developed our electronics with your chip nRF52840, but we have problem with communication throught BLE. We tried our firmware on dev kit with this chip. It was...
Hello,
I am looking for wireless communication solution between two devices with a maximum distance of 5-10m for controlling a speed of the electric-assisted vehicle (basically...
Hi,
I use SDK 12.3.0 with PCA10040 board, and try running experimental_ble_app_buttonless_dfu. It works fine when I use Keil to compile, but doesn't when use GNU. I open...
Hi,
I've tried connecting to the nRF52840 Dongle using nRF connect as explained in : ://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.tools%2Fdita%2Ftools...
Hi, I've been trying to build a custom characteristic and so far I can display a single digit number on my BLE app. My update value function looks like this:
And my add...
I am using SEGGER Embedded Studio to program the nRF51822 module. When I was going through the manual for setting up the environment for SEGGER Embedded studio, I found that...
I want to use a buzzer on my board.
The environment in use is below. · SDK15 · Nrf 52 · Nrf 52832_xxaa · S132_nrf52_6.0.0_softdevice.hex
My start is "nRF5_SDK_15.0.0_a53641a...
Hi support team,
I'm using a PDK(PCA10056) with nrf52840 and SDK 15.0. Recently I was developing a BLE bootloader for DFU OTA.
Since the ble bootloader was depended on...
Hi
I have been trying to get example ble_app_hrs to run after compilation on my 52832 dev board (pca10040).
The specific example is: C:\Keil_v5\ARM\PACK\NordicSemiconductor...
