Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hello,
I have the following setup:
A Raspberry Pi 3 B and a nRF52840 Development Kit acting as a Border Router as described here
Another nRF52840 Development Kit...
Hi there,
I'm trying to run the beacon s130 pca20006 example on a custom board. There are 2 main differences between the pca20006 and my board:
There is a 32 Mhz...
Hi,
it seems there was lately a new IC revision release of the nRF52840.
Is the nRF52840 IC Revision Engineering B 100% pin compatible to Engineering A, i.e. pinning...
Please excuse my basic question but I'm new to this - I am needing to have data collected from probe/sensor, which would be in a device, sent every hour to an android app...
Hello,
We plan to switch between two sets of UART pins for factory testing. One set will talk to an IC in our design and the other to a USB port through FTDI. Since simultaneous...
Hello,
We'd like to connect 50 bluetooth 5 devices (nRF52840) to a Receiver (made of multiple centrals nRF52840) with a long range (PHY 250kbps, conn interval 50ms, no...
We are evaluating the nRF5 SDK 13.0 to upgrade our projects from v12.0 and it looks like it has a bug related to the FDS functionality.
I managed to reproduce it on the...
Hi friends,
I am doing a project in NRF24le1 using RF communication with multiple nodes with a host using star topology.
Could you suggest a Protocol that supports connecting...
Hi,
to what impedance shall the BT antenna be matched?
Copying from the datasheet:
A matching network is needed between the RF pin ANT and the antenna, to match the...
Requests for the FW:
Add characteristic to access general GPIO pins in analog and digital form.
extension of the existing MOS_1-4 access, PIN read/write under the...
Hi,
We use nrf51 SDK v9. I found there are two SER_MAX_CONNECTIONS defined both in app_ble_gap_sec_keys.h and ser_config.h. Their values are different. One is referred...
Hello,
I have a problem when I try to use cheaper Android phones to communicate with our 52832 chip.
I can discover the peripheral and then connect, but when I device...
Hi,
I flashed softdevice and ble_app_UART_c code. But after searching bt device, i could not find bt nrf52 device in mobile.
Do i need to something more..
hi,
i am using nrf52840. with sdk 14.1. i am trying to broadcast my dk as beacon. with your neccessary examples. i have created my own services and started advertising. when...
I want to transfer data using UART to BLE by Baud Rate 460800 up to(using nRF52832).
I need to send a file, its size is 100MBytes
However, the use of examples(14.0vesion...
