Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Dear all,
I have a critical problem about mesh network.
After running 2 days, some device in mesh network cannot publish message with error 15 ( forbidden ).
I tried...
We see an increased power consumption at around 26uA when enabling GPIOTE IN events in our application with a NRF52840_xxAA_REV1 chip. We use nRF5_SDK_15.2.0_9412b96 and the...
Hello,
I would like to use the NRFsniffer firmware on a Sparkfun NRF52832 Breakout board and I cannot use the UART pins expected by the NRFsniffer since one of them is mapped...
Hi everyone,
I am a new developer and I am using the nRF52840 with SDK16 and s140 for prototyping and I have some questions about the bootloader and the softdevice.
Regarding...
Hi Nordic,
I am using simple LED blinky project on nRF52840, referenced from here.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/boards/arm/nrf52840dk_nrf52840...
I ran into a problem that some parameters that I change in the device tree are not applied.
For example: The resulting zephyr.dts file contains this setting:
in <devicetree_unfixed...
Hi .. i want to send the temperature data to central in non connectable state ,( in advertising ), as well as data will change dynamically . Therefore how to broadcast the...
Hello We are using the nRF52840-DK with SDK version 16.0.0 connecting to an android device Galaxy Note 5 (SM-N920v, Android 7.0, API 24). I captured the HCI_Snoop.Log (viewable...
I am using this code on all 3 nrf52 Development kit ( DK ) for server, client and relay+proxy nodes as mentioned in below setup...
1) nrf DK named A works as on/off server...
Hello, I'm trying to map custom PIN mapping on my prototype board, based on nRF9160 DK. I had to remove the UART0 pins and map them for my purpose, but when I'm trying to...
In nRF SDK 1.2.0 and 1.3.0, there is a function to generate the public/private RSA keys in http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrfxlib/nrf_security...
I want to develop the tool to download the firmware，so，I need to call the interface of nrfjprog.dll，but there aren·t the detailed descreption，who can teach me？
Question...
Hello, I am working on bare-metal with the BSDLib on a custom board. When trying to debug a specific case in which our server refuses TLS connection, I wanted to see which...
