Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using the NRF52840 and SDK15.3. My goal is to sign a payload using RSA and then verify on the NRF side of things.
The signing scheme is done with openssl on my computer...
Hello!
Is it possible to supply the Nordic Thingy:52 board from an external supply, different than the battery (for example, through the USB)?
I only see the battery option...
Hi all,
I wanna connect an accelerometer sensor the nRF52840 DK board. I think it should be connected physically at the pins P0.17, P0.19-P0.23. But the thing is, those...
hello Nordic
i want to use the bl652 laird development board (nrf52832) as a debugger for the nrf52840 dongle
i have been working with that board allready so it has...
Hi,
I'm trying to implement Eddystone beacons in my application.
My application is already contains advertisement feature with whitelist.
When I'm trying to use...
Hello,
Does anyone have some recommendations about what crystal to use with nRF52840?
We have been using FA-20H 32.0000MF10Z-AJ0 but now it is not in stock and we need...
Hello,
I have configured MQTT over TLS to connect to our broker. Everything works great except that the modem stops reconnecting to the broker after exactly 22 connect-disconnect...
Hi, I'm trying to run the nfc_pairing example from the master branch (1.3.99) of NCS. I've successfully built the example in SES and loaded it onto my nRF52840DK, but the...
I'm wondering how BLE signals are handled at the layer below the scanning module. Namely, suppose there are hundreds of BLE modules that are all advertising nearby. How does...
Hi
We are developing a 70 x 70mm PCB containing a nRF52840 for BLE/ESB and a second module for WiFi/BT.
We have no mechanism to avoid transmission of the WiFi module while...
Hi. Sorry, can't find the answer on the forum on my problem.
I am using:
nRF52840 DK
Segger
MacOS
Fanstel BC840 module
I have a project that flashes to Raytac...
Are there any examples of how to enable and use coded phy long range with the nRF Connect SDK? I have the nrf52840DK and would like to create an advertising example to test...
Hello,
In my current project designed around nRF52840 incorporating many peripherals (limited power budget) and many central devices. Each peripheral can connect to any...
Hi
I am using NRF52810 with Softdevice S112 7.0.1 and SDK 16
I want to ask about the behavior of the softdevice notification queue on disconnect. I have seen these two...
