Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I have seen some variations of this issue but hoping someone can lead me in the right direction.
Similar to others, I am using NRF_LOG_INFO for debug messages. It works...
Hello, I am working on a project which uses nrf52832 module ( https://www.seeedstudio.com/MDBT42Q-nRF52832-based-BLE-module.html ). I just want someone to review its circuit...
Hi!
I'm slightly confused with the documentation regarding softdevices S112 and S113. Among other differences, its noted that SD S113 does not support nrf52820 chipset while...
Hi, I have a custom board based on nRF9160 for which I created custom .dts following porting guide. It seems TX isn't sending anything (stay close to 0V) - config I have is...
I
I want to start a sample project on NRF 9160DK and I am facing some issues. I am following the link ( https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting...
Hi all,
I'm testing the ble_nfc_pairing_reference example from SDK 15.2.0
I have installed microECC and then run succesfully the application using Segger Embedded Studio...
Apologies if this has been asked a bunch of times but none of the posts I ran into were helpful. This is my first time working with a dongle of this nature so apologies if...
Hello,
i am using nRF52832 with Nordic SDK 16.0.0 and s132 7.0.1
in my project i have developed start and stop advertising API and added dis service in project
also...
Hello.
I need mqtt ble router running with android app.
infocenter.nordicsemi.com/.../iot_sdk_app_mqtt_publisher.html
https://infocenter.nordicsemi.com/topic/com.nordic...
We have recently ported a design from the nRF52832 to the nRF52840 using SDK 15.2.
During power profiling we have found the new design with the 840 chip is pulling more...
Hi,
In my project, there is a device lock up and I found the problematic point that a debug log using nrf_serial_write() in critical region.
I think it is not a good idea...
Hi there Devs,
My app is based on ble_app_blinky_c where I added a couple TWI sensors where check periodically every 10s and also scan for peripherals about every 10s...
Hello mates, Im trying to run this proyect:
nrf52-spi-i2c-master-ssd1306 ( github.com/.../nrf52-spi-i2c-master-ssd1306 )
I have the display and that kit development...
Currently I want to build the light_switch examples from the nrf5_SDK_for_Mesh_v2.2.0 on my nrf52832 dev board but this gives the following error "boards.h: No such file or...
