I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello,
I have successfully flashed and run the mqtt-simple example from the nrf samples with the default configuration.
If I run it 10 times in a row, the getaddr with...
Hi.
I struggled to migrate ble blinky example of nrf5 (nrf51422) to nrf51822 using KEIL (SDK5 v12.3) but failed
Here are what I tried.
Firstly, I changed target device...
Hello,
I want to create a program for communication and control between the NRF module and the desktop. I followed the instructions Installing from https://github.com/NordicSemiconductor...
Hi!
I'm working on a toy based on the nRF52810.
The BLE requirements are very low:
- Peripheral only
- 1 link only
- No bonding/pairing, no encryption, no whitelist...
i can create three service each with one notifiable characteristic. i am using nrf connect to test if it is work and i am able to send data through UART Rx and then enabled...
HI,
I'm use nrf51822 and SDK 10. I want to use APP_ERROR_CHECK function to show error msg, I did also enable LOG function to support this, but it do not work.
here is...
HI everyone!
My case:
nRF52832 + toolbox on iOS and Android
I have device pre-programmed using seeger with settings:
Next I want to make DFU update using .zip...
I am trying to receive data from GPS L80 with the nrf52832 board but I am not able to receive anything. I connected the Rx of nrf52832 with GPS and vice versa. I also connected...
Hello, I'm trying to get manufacturer specific data from peripheral, but I don't know how to do this when the peripheral is using extended advertisement with LE Coded PHY...
Currently, I am trying to create a UART connection between the nRF52840 Dongle and my PC. I am working with the usbd_ble_uart example found in the dongle SDK. I managed to...
Hi,
I am using nRF52840 Preview DK with SDK v15.3.0 and Softdevice version 6.1.1
I modified the Blinky peripheral code to advertise over Coded Phy, this code is working...
Hi all,
We are working on a project that requires us to measure the resistance of something applied externally. We are mainly interested in the change of resistance over...
Hi, I have managed to send data to a dedicated server, but I have a problem with reconnection. After re-connection, this is what I get as an output. In the log, there are...
Hi, I'm using Nrf52840 as the MCU for the developed product.
For my product, there is a central and a peripheral which two are communicate with each other via bluetooth...