Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I want to connect nRF52832 with PC. The objective is using nRF52832(I am using BT832 Module) I have to scan all Blue Tooth deceives details and send to PC. Please help with...
Hi,
I am using a custom board with the nrf52832 with SDK 13 and I have a bootloader and an application that both configure and feed the WDT.
However, upon restart (power...
Is there any straight forward way to detect jamming using any technique on this Nordic device? I'm using SDK 15.2, Soft-Device 6.1 Would this be possible by the new SD 6 function...
I have been using SMD modules with NRF24L01+ fitted.
The first batch I used worked fine for months.
Then I purchased another batch and found the tx_ds_active or max_rt_active...
Hi,
1. I went through the document. I'm trying the example applications Light-Switch on PCA10040 DK and NRF5 SDK for Mesh V2.2.0. So it is like the Client will be provisioned...
Good afternoon,
Following up my previous case, to which I got no reply, how can I use a queued write characteristic to write less than 20 bytes of data?
I'm using it...
I'm trying out Zephyr on the nRF52 DK, specifically I want to test the ADC drivers. Since things are moving quite fast in the Zephyr development world, there may be some information...
Hello, I'm working on Mesh SDK 2.1.1 and I'm trying to send a Relay Set message through Configuration Client. I have changed the code of models_init_cb() function inside the...
The nrfx_spim driver has an issue when chip select pin of the driver is not used.
When nrfx_spim_init is called with a nrfx_spim_config_t whose ss_pin is set to NRFX_SPIM_PIN_NOT_USED...
Dear Nordic
I have custom board(nRF52840) its not detecting through Jlink (from nRF52 DK).
I tried to connect nRF52840 dongle(using J2 in dongle) with same setup its detected...
Hi,
I am latest SDK 15.0, and using FDS library to store custom data. I have followed FDS examples but couldn't succeed in writing data to flash. When i tried to debug,...
Hi Guys,
We started to develop a mesh network with nRF52840 DK's and dongles. I have made some adjustments in the code with segger to use the server example of the led switch...
I just want to globally set the power level, and forget about it.
I have seen this post, and it still seems unclear how to do this - or if it's even possible.
Is there...
Good afternoon,
I had a question regarding scanning and pairing. Is it possible for a peripheral device to send scan requests after its been paired? or does the device have...
