Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
When calling nrf_drv_twi_tx() once like in the snippet below it works, but when the function is called two or more times sequentially, it fails. However running a nrf_delay_ms...
With respect to Softdevice versions SDK_14.2.0_17b948a and SDK_15.0.0_a53641a
I have a question about softdevice function:
sd_ble_gap_lesc_dhkey_reply()
and its parameter...
Hi Sir,
In this project, we design w/ nRF51802-QFAA (Flash: 256KB, RAM: 16KB) and developed the application and bootloader through the nRF51-DK (pca10028).
We can test...
Apologies if this is a duplicate post:
I am successfully making nRF example apps in nRF5_SDK_12.3.0_d7731ad using GNU Tools Arm Embedded version 7 2018-q2-update in Windows...
Hi,
I want to use both UART0 and UART1 at the same time, and run the testing example from https://devzone.nordicsemi.com/f/nordic-q-a/25173/nrf52840-uart1-not-working-in...
Hello,
Using two nrf52 Dev Kit boards for Central / Peripheral. Using Softdevice S132, , peer manager and Segger on Win7.
I have modified ble_uart_and ble_uart_c using...
Hi,
I have downloaded the nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac and try to compile the zigbee_light_switch_pca10056 example under segger embedded studio and I have...
We are developing a standalone application. The bulk power is provided by LiPo battery, which can vary from 4.2V to 3.0V as the battery discharges. I have the system connected...
I recently added bonding and authentication to my application. I have two characteristics with CCCDs and they are both broken. One characteristic is "protected" (requires...
Is there a standard/spec for the UUID used for provisionee devices?
I don't see anything in the mesh examples that indicates a standard UUID format is used.
It allows...
I am using an nRF52 DK with Soft Device 6.1.0 on a Windows platform.
I am trying to add a new BLE Service and calling function sd_ble_uuid_vs_add() but get NO_MEM error...
I am developing three different projects for the nRF51822 using SDK 12.3 and the app_uart_fifo code module. Details of the projects are as follows:
Project 1 - implemented...
I am attempting to run the mesh Light Switch example with a provisioner, client and a server in debug mode using the Segger SES. I am attempting to debug the server code on...
Hello everyone, the sdk version that I use is 15.0.
I'm trying to connect my nRF52832 (master) to an external SPI slave memory (N25Q) to write and read data. The problem...
Hi Everyone,
RFX2411N is used to extend signal coverage of NRF51822. Here are the configuration below:
Use radio notification to generate an interrupt
Use this interrupt...
