Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi:
I am using SDK14.0 S132 for nrf52832 , i found it's sleep mode power comsumption large than 5mA .
I am using internal LDO and external power is 3.7V li-battery cross...
Hi
Just to be sure: I've recently bought the nRF52840 Preview DK (dev board for nRF52840) but I think I'm going to use the nRF52832 instead for my project.
Is it ok to...
Hi i want to create a new project in Eclipse. I did this my following the complete code form git hub for devzone.nordicsemi.com/.../
*Nordic has provided sample code for...
Hi!
I've based a new project for the nRF52840/S140/Preview-DK on ble_central/ble_app_uart_c .
I use the NRF_LOG_XXXX macros for debug and they print fine in RTT Viewer...
Hi,
I have two nrf51822 device, on work as GAP Central, another work as GAP Peripheral.The two device use different connection parameters, after the connection is established...
hello,
i have developed one board using nRF52832-QFAA and trying to dump simple LED blinking code in it using nRF52 DK board. But code is always dumping into custom board...
How do you do
Now need pwm_driver demo5 duty ratio, is there any way to 1/6 or 1/8?PWM and phase difference is 4 road？
Ask for a few days, change seq_values [], but how...
I am developing firmware using S132 (SDK 11) for a custom board.
After performing Pstorage Update, if I do not wait for the callback from pstorage before continuing execution...
I am currently working with a the nRF5x bluetooth chip family and connecting to a windows 10 device as a central. I am using uart to get some visibility into what is happening...
Greetings -
I recently downloaded the latest SD140 images, 6.0.0-6-alpha, and began having issues with BLE communication.
I'm developing a custom device, based on the...
Hi to everyone!
I have a problem with the NRF_LOG or with RTT Viewer.
I wrote this simple code, just to test an output console.
int i = 0;
while (i< 100)
{
NRF_LOG_INFO...
When a Jlink programmer is connected to multiple devices (daisy chained) how do I specify which device is being programmed on the command line using nrfjprog?
Additionally...
Hi
I am making a speed cadence sensor.
I am using the gpio event handler to check the cumulative wheel revolutions and send the recorded value to the app as a time handler...
Hi,
Once the main hardware init part is done, system idles for a while and then I get a hardfault (APP_ERROR_CHECK returns fatal)
I reset the chip, and asked it to continue...
