Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi,
I am trying to program nrf52 (on board ), but I keep getting these error:
$ nrfjprog -f nrf52 --program nrf52832_xxaa.hex --eraseall
ERROR: JLinkARM DLL reported an...
Hi,
I'm trying to connect and discover services of a BLE device equipped with a nrf52832. The device advertises correctly and i can see it on the nrf Connect app on both...
Hi All,
i would like to know how gpio relate to gpiote,i go through some code and find
out , that gpiote handles in,out,config registers that is handle by gpio also ...
Hi nordic guys,
I have built a project based on ble_app_hids_keyboard demo in SDK12.3.0.This is a new hid deive which is microsoft defined in win10.The sample report is...
I have few questions on BLE in rigado based on my requirement needs,
I need Dynamic data transfer in beacon mode, is it possible in Beacon mode without Rigado BLE stack...
Hello,
I get two errors when compiling examples\ble_peripheral\ble_app_uart with IAR 8.11. I have ble_app_uart_pca10040_s132 - nrf52832_xxaa as the active project.
I...
registered_handler_get() in ble_db_discovery.c searches a table for the appropriate handler to call for a given UUID.
However, ble_db_discovery_evt_register() assigns the...
Hi,
In the Getting Started guide of the Bluetooth Mesh SDK it is stated that legacy non-mesh devices can communicate with the mesh via a proxy mesh device through tunneling...
Hi everyone,
I am using the PCA10001 eval board and I have been able to get things up and running using the mbed platform but now I am implementing a timer based interrupt...
Hi All,
I'm currently designing my implementation of BLE Services/Characteristics and wanted a quick review to make sure I'm on the right path based on my implementation...
Hi,
I have couple of nRF52832 boards, nRF5-SDK-for-Mesh (v. 0.9.2) and good will to demonstrate some simple multihop mesh.
I already tested the light control example...
Hello,
There is gonna be a tech tour in my country(Israel) soon and I am planning to purchase 2 nrf52832 Development kits does anybody know if it will be available there...
Hi! I want to use the "cube" animation from android thingy app, with my custom board.
When I scaned in first place I couldn't see my board. It was solved adding the ble_tcs...
Hi,
Is it safe to backfeed some current into the PPK.
I use the PPK to measure the power consumption of a battery powered IoT device. I disconnect the battery and use the...
