Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hello everybody, I'm new to the Nordic system and the nRF52. I'm trying to become familiar with the board and I want to be able to read different 4 input pins, each one attached...
I am using Segger embedded studio 3.1 with SD132 2.0.0 and a nRF52832QFAAB0.
I have verified that I am compiling against the correct header files. This service number for...
Hi, even if I set hal_nrf_enable_ack_payload(false) on the sender (and receiver), the receiver still sends back an ACK which i can detect in the NRF_ISR(). is this normal...
Hello,
I have a pca10028 and I am wondering if I can use it also to flash nrf52 boards.
I quickly tried with rknrfgo on mac to wipe a custom board based on nRF52832 and...
Hello.
I decided to use an external solution for RTC.
Sometimes the RTC chip offers an buffered 32.768KHz output.
Can I use this output to supply the 32.768KHz to the nRF52832...
I have set up raspberry pi 3 as a border router and programmed the the nrf51422 using the iot_ipv6_coap_server_pca10028 and could successfully switch on and off led3 and led4...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hai
i am using mbed to program my nrf5188. now i am using securityManager to implement a bonding between central and peripheral. now i need to know when a device is connected...
Hi,
In my code, I have not started the HF clock. I call the ble_stack_init where "SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, NULL);" is called. Which HF clock...
Hi, all.
I tested ble_app_uart in example directory by PCA10040 board.
The ble_app_uart includes "printf("\r\nUART Start!\r\n");" and "UART Start!" cames out on the putty...
I have a scenario where I have multiple peripherals (nRF52) and multiple centrals (cell phone).
The user is going to use only one central with only one peripheral together...
Hello
In case a connection is disconnected locally by calling sd_ble_gap_disconnect(), no BLE_GAP_EVT_DISCONNECTED is fired even though the sd_ble_gap_disconnect() function...
Hello, I'm trying to optimize power on HID Keyboard app.
This post was helpfull but yet some questions remains.
If I use several services, and want central to be abble...
After S110 7.1 ble_stack_init(), any read/write to temperature register cause a HardFault.
Some sentences like:
nrf_temp_init();
NRF_TEMP->TASKS_START = 1;
...
Hi --
I am using the ble_peripheral/ble_app_hrs example project. And if I try to update the vs_uuid_count param to 2. It proceeds to fail the softdevice_enable with error...
