We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
I am frustrated by a pair of nRF24L01+ communicating with each other, where all the Enhanced ShockBurst features are enabled.
The PRX is initialised as follows...
I could scan/detect Beacons, and I could update the configuration without any problem with the nRF Beacons app. The issue is that the configured Beacons are not detected in...
Hi,
I want to use the nRF51 dongle with the Master Control Panel.
I found in the nRF51 Dongle User Guide that the Dongle will run with the Master Emulator firmware, but...
I don't expect the Nordic engineers to know this answer but I'd like to hear from other devs out in BLE land...
Have any of you encountered truly horrible BLE PHY-level...
I am using S120 device to receive advertising from S110 device and need to get the exact time + sender's address information at Radio End Event.
I use PPI to start Timer1...
Hi,
I'v try to use the sd_power_system_off() and without successful.
The power consumption will be 200~230uA around.
My device:
Call the system off when ADV._TIMEOUT...
Hi
I am trying to make a ble central with s120 on a pca10001 board.
My problem is that it sometimes take a lot of time (up to 10 seconds) to find the client when i make...
Hello Nordic guys, help requested !!!
Error while connecting to USB port the new development boards, DK and DONGLE.
Error is " OS X unable to repair JLINK disk ".
...
Hi,
is it possible to use Nordic SDK with nRF51822 to have capacitive touch sensing with 2 dsital inputs, just as the mbed or avr library capsense?
MBED: developer.mbed...
Hi, i have a strange issue on connecting nRF24L01+ module to Arduino pro mini. I use arduino pro mini, nrf24L01+ module, 3.7V 6000mah battery and DS181 chip to measure temperature...
Hi,
When I start the TX sweep test with all 80 channels I get only 10 channels used by the RF.
Also power strength of the channels is modulated.
cf. attached frequency...
Hi
I am developing an iOS app that needs to communicate to an nrf51822(working in ble peripheral mode). The peripheral to which the app connect is selected using mac address...
hi nordic team：
I was wondering if the main program is too complex, and do not use the scheduler, and the connection parameter settings are correct. Whether because the...
Hello,
I have tested the DFU and everything works fine. Normaly the device enters into DFU mode with a pressed button 7, meaning the level on I/O 7 is LOW.
But in my...
Hi,
I've an HardFault, the program crash to the HardFault service routine at this row of the twi_hw_master.c:
--> NRF_PPI->CH[0].EEP = (uint32_t)&NRF_TWI1->EVENTS_BB;...
