Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi,
We are using nRF51422 in our project and we observe a strange thing, that even there is no external pull up resistors, the I2C communication using the built-in TWI...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Hi,
I am trying to create a star network with 12-16 slaves and one master.
The master would be a nrf51822 and the slaves nRF8001/2.
The slaves would not transmit...
Hi,
I'm using the UART_OVER_BTLE base example and I'm investigating what needs to be done to enable security.
Using the Following security configuration the device stops...
Can you tell me which antennaes i can connect with nRF 8001 to make it discoverable and transfer data. And i think pi network is solved depending on the antennae only. Can...
Hi,
Is it possible to extend the RAM memory by using internal flash memory?
Actually i need to collect 4KB of data from accelerometer and flash it to the EEPROM when there...
I'm working on a device which may spend months, or even years as deep as 1000 ft underwater...a harsh environment. Accordingly, the PCB will be completely encased in plastic...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
The 10000 dongle does get detected in nrfgo Studio but the 10001 board does not. There are no USB devices with exclamation marks or otherwise undetected when the 10001 is...
Hey folks,
I am currently trying to expose a local name for my nrf51822 chip but whenever i change it from NO_NAME to any of the other options and run the program it doesn...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
Hi,
I need the 16 bit timer1 to have high priority, how do i set this to a high priority? And what priority does it have in my case when i use:
NVIC_EnableIRQ(TIMER1_IRQn...
Hello
I have a nRF51822-EK evaluation kit, I have succesffuly installed the nRFgo studio and Seggger software so that I can detect the dongle and it shows up on device...
I compiled HID_KEYBOARD on two computers.
One doesn't have any problem, but another has...
I tried to connect with I-phone, but i couldn't find I-phone connection. ...
